Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Determination of Sludging and Corrosion Tendencies of Inhibited Mineral Oils (Includes all amendments and changes 11/10/2022).
Přeložit název
NORMA vydána dne 1.11.2022
Označení normy: ASTM D4310-22a
Datum vydání normy: 1.11.2022
Kód zboží: NS-1088966
Počet stran: 12
Přibližná hmotnost: 36 g (0.08 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
antiwear hydraulic oils, circulating oils, copper, corrosion, hydraulic oils, inhibited mineral oils, insoluble material, metal catalysts, oxidation, sludge, steam turbine lubricants, turbine oils,, ICS Number Code 75.040 (Crude petroleum)
Significance and Use | ||||||||||||||||||||||
5.1?Insoluble material may form in oils that are subjected to oxidizing conditions. 5.2?Significant formation of oil insolubles or metal corrosion products, or both, during this test may indicate that the oil will form insolubles or corrode metals, or both, during field service. However, no correlation with field service has been established. |
||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||
1.1?This test method covers and is used to evaluate the tendency of inhibited mineral oil based steam turbine lubricants and mineral oil based anti-wear hydraulic oils to corrode copper catalyst metal and to form sludge during oxidation in the presence of oxygen, water, and copper and iron metals at an elevated temperature. The test method is also used for testing circulating oils having a specific gravity less than that of water and containing rust and oxidation inhibitors. Note 1:?During round robin testing copper and iron in the oil,
water and sludge phases were measured. However, the values for the
total iron were found to be so low (that is, below 0.8 mg), that
statistical analysis was inappropriate. The results of the
cooperative test program are available (see Section 16).
1.2?This test method is a modification of Test Method D943 where the oxidation stability of the same kinds of oils is determined by following the acid number of oil. The number of test hours required for the oil to reach an acid number of 2.0 mg KOH/g is the oxidation lifetime. 1.3?Procedure A of this test method requires the determination and report of the weight of the sludge and the total amount of copper in the oil, water, and sludge phases. Procedure B requires the sludge determination only. The acid number determination is optional for both procedures. 1.4?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5?1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 03.11.2024 (Počet položek: 2 209 203)
© Copyright 2024 NORMSERVIS s.r.o.