Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Rheological Properties of Paste Printing and Vehicles by the Falling-Rod Viscometer
Automaticky přeložený název:
Standardní zkušební metoda pro reologické vlastnosti Vložit Tisk a vozidel Falling-Rod viskozimetru
NORMA vydána dne 1.2.2010
Označení normy: ASTM D4040-10
Poznámka: NEPLATNÁ
Datum vydání normy: 1.2.2010
Kód zboží: NS-25814
Počet stran: 10
Přibližná hmotnost: 30 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
apparent viscosity, falling-rod viscometers , inks, non-Newtonianism, power law viscosity, printing inks, shortness, vehicles, viscometers, viscosity, yield value, Calibration--paints/related coatings analysis instrumentation, Falling rod viscometer, Glazing compounds/applications, Newtonian fluids, Non-Newtonian coatings, Power law, Printing inks/vehicles, Shear testing--paints/related coatings/materials, Sliding scale calibration graph, Viscometers--falling rod
Significance and Use | ||||||
Apparent viscosity at the relatively high shear rate of 2500 s−1 does not completely define the rheological properties of printing inks but is useful in the practical control of ink viscosity during production and the specification acceptance between supplier and purchaser. The slope of the power law plot is the preferred measure of non-Newtonianism. The yield value, which is obtained by extrapolation of high-shear measurements to a shear rate approaching zero, does not conform to the definition of the true yield stress (see 3.1.7). The yield value and other low shear parameters are also subject to a high degree of variability (see the precision table in Section 17). |
||||||
1. Scope | ||||||
1.1 This test method covers the procedure for determining the falling-rod viscosity and degree of non-Newtonian behavior of printing inks, vehicles, and similar liquids that are essentially nonvolatile and unreactive under ordinary room conditions. 1.2 For printing inks, which are typically non-Newtonian, this test method is applicable in the apparent viscosity range from about 10 to 300 P at a shear rate of 2500 s−1. For Newtonian liquids, the applicable viscosity range is about 10 to 1000 P (1 P = 0.1 Pa·s). 1.3 This test method uses a falling-rod viscometer in which shear conditions are altered by manually adding weight to the rod. A fully automatic instrument is described in Test Method D6606. 1.4 This test method, as does Test Method D6606, bases calculations on the power law model of viscosity. ISO 12644 covers not only the power law but also the Casson and Bingham models. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8. |
||||||
2. Referenced Documents | ||||||
|
Historická
1.6.2012
Historická
1.1.2014
Historická
1.12.2010
Historická
1.11.2013
Historická
1.6.2013
Historická
1.6.2013
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 21.11.2024 (Počet položek: 2 206 478)
© Copyright 2024 NORMSERVIS s.r.o.