Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM D3754-03

Standard Specification for ""Fiberglass"" (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe

Automaticky přeložený název:

Standardní specifikace pro " skleněných vláken " ( Glass - Fiber - Reinforced Teplem - pryskyřice ) Kanalizace a průmyslové tlakové potrubí

NORMA vydána dne 10.5.2003

Jazyk
Provedení	Online zabezpečené PDF - 1 979.50 Kč Tištěné - 1 979.50 Kč
Dostupnost	SKLADEM
Cena	1979.50 Kč bez DPH
1 979.50 Kč

Informace o normě:

Označení normy: ASTM D3754-03
Poznámka: NEPLATNÁ
Datum vydání normy: 10.5.2003
Kód zboží: NS-24730
Počet stran: 14
Přibližná hmotnost: 42 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM D3754-03 :

Keywords:

drainage systems-sewer/drain pipe (thermoplastic), fiberglass (glass-fiber-reinforced resin) sewer/industrial pressure, glass-fiber-reinforced thermosetting-resin ("fiberglass"), "fiberglass" pipe, for sewer/industrial pressure applications, spec, Plastic pipe/tubing/fittings-reinforced thermosetting resin (RTR), fiberglass (glass-fiber-reinforced thermosetting resin) sewer/industrial, pressure pipe

Doplňující informace

1. Scope

1.1 This specification covers machine-made fiberglass pipe, 8 in. (200 mm) through 144 in. (3700 mm), for use in pressure systems for conveying sanitary sewage, storm water, and many industrial wastes, and corrosive fluids. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are fiberglass pipes. This standard is suited primarily for pipes to be installed in buried applications, although it may be used to the extent applicable for other installations such as, but not limited to, sliplining and rehabilitation of existing pipelines. Pipe covered by this specification is intended to operate at internal gage pressures of 250 psi (1.72 MPa) or less.

Note 1—For the purposes of this standard, polymer does not include natural polymers.

1.2 The values given in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

Note 2—There is no similar or equivalent ISO standard.

1.3 The following precautionary caveat pertains only to the test method portion, Section 8 , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D2992-24	Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
D3567-17(2022)	Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D3681-23	Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
D883-26a	Standard Terminology Relating to Plastics (Includes all amendments and changes 6/15/2026).
C33-07	Standard Specification for Concrete Aggregates
C581-26	Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
D638-22	Standard Test Method for Tensile Properties of Plastics
D695-26	Standard Test Method for Compressive Properties of Rigid Plastics
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ISO?1172	Textile Glass Reinforced Plastics--Determination of Loss on Ignition Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
AWWA C-950	Glass-Fiber Reinforced Thermosetting Resin Pressure Pipe Available from American Water Works Association (AWWA), 6666 W. Quincy Ave., Denver, CO 80235, http://www.awwa.org.
F412-25a	Standard Terminology Relating to Plastic Piping Systems (Includes all amendments and changes 10/8/2025).
D790-25	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics
D4161-24	Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D2290-25	Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
D2412-26	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2584-25	Standard Test Method for Ignition Loss of Cured Reinforced Resins

Doporučujeme:

Aktualizace technických norem

Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.

Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.