Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Norma ASTM D3667-16(2022) 1.10.2022 náhled

Doplňující informace

ASTM D3667-16(2022)

Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors

Přeložit název

NORMA vydána dne 1.10.2022

Jazyk
Provedení	PDF - okamžité stažení - 1 474.20 Kč Tištěné - 1 474.20 Kč
Dostupnost	SKLADEM
Cena	1474.20 Kč bez DPH
1 474.20 Kč

Informace o normě:

Označení normy: ASTM D3667-16(2022)
Datum vydání normy: 1.10.2022
Kód zboží: NS-1088703
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Těsnění, ucpávky

Anotace textu normy ASTM D3667-16(2022) :

This specification covers the general requirements for materials used in rubber seals of flat-plate solar collectors, except vertically mounted passive collectors. Particular applications may necessitate other requirements that would take precedence over these requirements when specified. The rubber seals are classified into types, grades, and classes: type C - intended for use in cold climates, and type W - intended for use in warm climates; grades 2, 3, 4, 5, 6, 7, and 8 that differ in hardness properties; class PS - preformed rubber seal, and class SC - sealing compound. Seals shall be rubber vulcanizates conforming to the requirements prescribed. The adhesion, volatiles lost, and volatiles condensable shall be tested to meet the requirements prescribed.

Keywords:

flat-plate solar collectors, preformed seals, rubber, sealing compounds,, ICS Number Code 21.140 (Seals, glands)

Doplňující informace

1. Scope

1.1?This specification covers the general requirements for materials used in rubber seals of flat-plate solar collectors, except vertically mounted passive collectors. Particular applications may necessitate other requirements that would take precedence over these requirements when specified.

1.2?The design requirement pertains only to permissible deflections of the rubber during thermal expansion or contraction of the seal in use and the tolerances in dimensions of molded and extruded seals.

1.3?This specification does not include requirements pertaining to the fabrication or installation of the seals.

1.4?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5?The following safety hazards caveat pertains only to Section 9, Test Methods, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

G155-21	Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials
G151-19	Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
D1349-14(2019)	Standard Practice for Rubber´Standard Conditions for Testing
C717-19	Standard Terminology of Building Seals and Sealants
C719-22	Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
D395-18	Standard Test Methods for Rubber Property´Compression Set
D412-16(2021)	Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D865-11(2018)	Standard Test Method for Rubber´Deterioration by Heating in Air (Test Tube Enclosure)
D1149-18	Standard Test Methods for Rubber Deterioration´Cracking in an Ozone Controlled Environment
D1229-03(2019)	Standard Test Method for Rubber Property´Compression Set at Low Temperatures
C661-15(2022)	Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer
D2137-11(2018)	Standard Test Methods for Rubber Property´Brittleness Point of Flexible Polymers and Coated Fabrics
D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D1415-18	Standard Test Method for Rubber Property´International Hardness
D1566-21a	Standard Terminology Relating to Rubber (Includes all amendments and changes 11/10/2021).
D3182-21a	Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets (Includes all amendments and changes 11/12/2021).
D3183-10(2019)	Standard Practice for Rubber´Preparation of Pieces for Test Purposes from Products
G7-05	Standard Practice for Atmospheric Environmental Exposure Testing of Nonmetallic Materials
RMA Handbook

Doporučujeme:

Aktualizace technických norem

Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.

Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.