Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D3412/D3412M-13(2020)
Standard Test Method for Coefficient of Friction, Yarn to Yarn
Přeložit název
NORMA vydána dne 1.2.2020
Informace o normě:
Označení normy: ASTM D3412/D3412M-13(2020)
Datum vydání normy: 1.2.2020
Kód zboží: NS-988565
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D3412/D3412M-13(2020) :
Keywords:
coefficient of friction, yarns, yarn to yarn,, ICS Number Code 59.080.20 (Yarns)
Doplňující informace
| Significance and Use | ||||||||||||
|
5.1 This test method for testing yarn-to-yarn friction is being used, but is not recommended, for acceptance testing of commercial shipments since between-laboratory precision is known to be poor. 5.1.1 In some cases, the purchaser and supplier may have to test a commercial shipment of one or more specific materials by the best available method even though the method has not been recommended for acceptance testing of commercial shipments. In case of a dispute arising from differences in reported test results when using Test Method D3412/D3412M for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's 5.2 This test method is intended for the determination of yarn-to-yarn boundary friction coefficients measured over a specified length of yarn. 5.3 The test method is useful for quality control, research, and the characterization of yarn boundary lubricants. Note 3: Because the geometry of the yarns is different,
Options 1 and 2 should not be expected to give the same numerical
values on the same yarns.
|
||||||||||||
| 1. Scope | ||||||||||||
|
1.1 This test method covers the measurement of frictional properties for both continuous filament and spun-staple yarns under boundary friction conditions. 1.2 This test method has been used with yarns having linear densities ranging from 1.5 to 400 tex, but may be used with yarns outside these ranges [15 to 3600 denier]. Note 1: For coefficient of friction, yarn to metal, see Test
Method D3108/D3108M.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
