Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D3159-22
Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials
Přeložit název
NORMA vydána dne 15.3.2022
Informace o normě:
Označení normy: ASTM D3159-22
Datum vydání normy: 15.3.2022
Kód zboží: NS-1052378
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D3159-22 :
This specification covers melt processible molding and extrusion materials of modified ETFE-fluoropolymer. The ETFE resin is a copolymer of ethylene containing approximately 75 mass% of tetrafluoroethylene. This specification addresses virgin materials only as performance requirements cannot be met with recycled material. Modified ETFE-fluoropolymers shall be supplied in pellet form and classified into five types according to their specific gravity. Furthermore, the resins of each type are divided into three grades according to their melt flow rate. Materials shall be sampled, prepared, and conditioned as appropriate for testing, wherein the following performance requirements must be met: melting point and flow rate; melting endotherm peak temperature; specific gravity; tensile properties (tensile strength and elongation); and dielectric constant and dissipation factor.
Keywords:
ETFE fluoropolymer, extrusion material, fluoropolymers, melt-processible fluoropolymer, molding material, recycled, tetrafluoroethylene copolymers, tetrafluoroethylene-ethylene copolymers,, ICS Number Code 83.080.20 (Thermoplastic materials)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||
|
1.1?This specification covers molding and extrusion materials of modified ETFE fluoropolymer. The ETFE resin is a copolymer of ethylene and tetrafluoroethylene. Modified ETFE resin contains no more than 5 mole % of other fluoromonomers. 1.2?The values stated in SI units as detailed in IEEE/ASTM SI-10 are to be regarded as standard. The values given in parentheses are for information only. Note 1:?Although this specification and ISO 20568-1 and ISO
20568-2 differ in approach or detail, data obtained using either
are technically equivalent.
1.3?The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?Recycled material is not appropriate for this specification because performance requirements cannot be met with recycled material. Therefore, this specification is for virgin material only. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
