Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D3032-21a
Standard Test Methods for Hookup Wire Insulation (Includes all amendments and changes 6/10/2021).
Přeložit název
NORMA vydána dne 1.4.2021
Informace o normě:
Označení normy: ASTM D3032-21a
Datum vydání normy: 1.4.2021
Kód zboží: NS-1027041
Počet stran: 39
Přibližná hmotnost: 117 g (0.26 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D3032-21a :
These test methods detail the standard procedures for testing hookup wire insulations including all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness or flat ribbon cable. The insulating materials include not only the primary insulation over the conductor, but also insulating jackets over shielded constructions. The test procedures covered here shall be performed in the conditions or shall determine the properties, as follows: axial stability (longitudinal change) after thermal exposure; bondability to potting compounds; capacitance; cold bend test; concentricity; crush resistance; dielectric breakdown voltage; dimensions; dry-arc tracking; dynamic cut-through; fluid immersion; high temperature shock; insulation-continuity proof tests; insulation resistance; partial discharge (corona) inception and extinction voltage; relative thermal life and temperature index; strip force; surface resistance; tensile properties; vertical flame test; voltage rating of hook-up wire; voltage withstand test; and wet arc-tracking.
Keywords:
ambient temperature, arcing, arc-propagation, arc-tracking, atmospheric pressure, breakdown voltage, cable, circuit breakers, current limiting, cuts, degradation, dropping apparatus, dry-arcing, electrical insulation, electrolyte, extinction voltage, flame propagation, flame spread, flame test, flammability, hookup wire, insulation thickness, moisture, open-circuit detection, partial discharge, power supply, safe voltage, scintillation, service condition, short-circuit detection
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1?These test methods cover procedures for testing hookup wire. 1.2?For the purposes of these test methods, hookup wire insulation includes all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness or flat ribbon cable. The insulating materials include not only the primary insulation over the conductor, but also insulating jackets over shielded constructions. 1.3?These test methods and their locations are as follows:
1.4?The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5?This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not, by itself, incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.6?Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
