Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Low-Temperature Viscosity of Lubricants Measured by Brookfield Viscometer
Automaticky přeložený název:
Standardní zkušební metoda pro nízkoteplotní Viskozita maziv, měřeno Brookfield
NORMA vydána dne 1.8.2009
Označení normy: ASTM D2983-09
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2009
Kód zboží: NS-22168
Počet stran: 14
Přibližná hmotnost: 42 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
Brookfield viscometer, Gear oils (GO), Low-temperature testing--petroleum products/applications, Lubricating oils, Temperature tests--petroleum products, Viscosity--petroleum products, ICS Number Code 75.100 (Lubricants, industrial oils and related products)
Significance and Use | ||||||||||||||||
The low-temperature, low-shear-rate viscosity of automatic transmission fluids, gear oils, torque and tractor fluids, and industrial and automotive hydraulic oils (see Annex A4) are of considerable importance to the proper operation of many mechanical devices. Measurement of the viscometric properties of these oils and fluids at low temperatures is often used to specify their acceptance for service. This test method is used in a number of specifications. This test method describes how to measure apparent viscosity directly without the errors associated with earlier techniques using extrapolation of experimental viscometric data obtained at higher temperatures. Note 1—Low temperature viscosity values obtained by either interpolation or extrapolation of oils may be subject to errors caused by gelation and other forms of non-Newtonian response to spindle speed and torque. Only in the case of known Newtonian oils at the temperature desired is interpolation acceptable for the purpose of calibrating the spindle and glass cell (see Annex A1). |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This test method covers the use of Brookfield viscometers of appropriate torque for the determination of the low-shear-rate viscosity of lubricants. The test is applied over the viscosity range of 500 to 900 000 mPa·s within a low temperature range appropriate to the capacity of the viscometer head. 1.2 The range of viscosity used to generate the precision data for this test method was from 1000 to 900 000 mPa·s. Appendix X4 lists another interlaboratory study that specifically targeted hydraulic fluid ranging from 500 to 1700 mPa·s. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1 The test method uses the SI unit, milliPascal-second (mPa·s), as the unit of viscosity. (1 cP = 1 mPa·s). 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Historická
1.5.2011
Historická
1.7.2011
Historická
1.12.2012
Historická
1.6.2012
Historická
1.12.2012
Historická
1.12.2012
Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 04.11.2024 (Počet položek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.