Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D2902-21
Standard Specification for Fluoropolymer Resin Heat-Shrinkable Tubing for Electrical Insulation
Přeložit název
NORMA vydána dne 1.3.2021
Informace o normě:
Označení normy: ASTM D2902-21
Datum vydání normy: 1.3.2021
Kód zboží: NS-1024143
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D2902-21 :
This specification applies to flexible fluoropolymer resin heat-shrinkable extruded tubing made from tetrafluoroethylene resin, copolymer of tetrafluoroethylene and hexafluoropropylene (FEP), and from perfluoroalkoxy (PFA) resin for use as electrical insulation. This specification covers three types of tubings, namely: Type I tubing, normally made by paste extrusion, and Type II and Type III tubings, normally made by melt extrusion. The finished compound shall be free of all foreign matter other than intended formulation additives. The material shall conform to the specified chemical and physical property requirements such as: (1) restricted shrinkage, (2) specific gravity, (3) longitudinal change, (4) tensile modulus at elongation, (5) volume resistivity, (6) dielectric breakdown voltage, (7) heat resistance, (8) low-temperature flexibility, and (9) melting point. The dimensional requirements after unrestrictive shrinkage such as inside diameter, wall thickness, and stock lengths are specified. The sampling and test methods to determine conformance to the specified requirements are given.
Keywords:
electrical insulation, FEP, fluoropolymer resin heat-shrinkable tubing, heat-shrinkable tubing, PFA fluoropolymer, PTFE,, ICS Number Code 29.035.20 (Plastic and rubber insulating materials),83.140.10 (Films and sheets)
Doplňující informace
| 1. Scope | ||||||||||||||||||||
|
1.1?This specification applies to flexible heat-shrinkable extruded tubing made from tetrafluoroethylene resin, copolymer of tetrafluoroethylene and hexafluoropropylene, and from perfluoroalkoxy resin for use as electrical insulation. This specification excludes crosslinked poly(vinylidene fluoride) and poly(vinylidene fluoride) copolymer which are covered under Specification D3144. Note 1:?This standard is similar but not identical to IEC
60684-3-240.
1.2?The values stated in inch-pound units are to be regarded as standard, except temperature, which shall be stated in degrees Celsius. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
