Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Resistance R-Value and Expansion Pressure of Compacted Soils
Automaticky přeložený název:
Standardní zkušební metoda pro odolnost proti R-Value a tlaku v expanzní hutného půd
NORMA vydána dne 1.3.2013
Označení normy: ASTM D2844/D2844M-13
Poznámka: NEPLATNÁ
Datum vydání normy: 1.3.2013
Kód zboží: NS-21684
Počet stran: 13
Přibližná hmotnost: 39 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Zemní práce. Hloubicí práce. Budování základů. Podzemní práce
Keywords:
acceptance tests, base course, bearing capacities, compaction, dynamic bearing capacity, expansion, expansive soils, flexible pavements, foundations, highway loads, inspection, kneading compaction, laboratory tests, material tests, pavement design, resistance value, specifications, stability, stabilometer, subbase, subbase strength, subgrade, subgrade reaction, subgrade stability, trafficability, ICS Number Code 93.020 (Earth works. Excavations. Foundation construction. Underground works)
Significance and Use | ||||||||||||||||||||||
4.1 This test method is used to measure the potential strength of subgrade, subbase, and base course materials for use in road and airfield pavements. The R-value is used by some agencies as criteria for acceptance of aggregates for base course and bituminous courses. FIG. 1 Tamper Shoe for Kneading
Compactor
4.2 The expansion pressure testing has been used in conjunction with the R-value test to determine cover requirements (thickness) and construction controls to reduce pavement distortion from expansive subgrade soils. 1.1 This test method covers the
procedure for testing both treated and untreated laboratory
compacted soils or aggregates with the stabilometer and expansion
pressure devices to obtain results indicative of performance when
placed in the base, subbase, or subgrade of a road subjected to
traffic.
1.2 Units—The values stated in either SI units or inch-pound units [presented in brackets] are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. However, use of equipment manufactured to be readable in inch-pound units only should not be considered as non-conformance to the test method. Many stabilometers and expansion pressure devices are manufactured to be readable in inch-pound units only. 1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.3.1 For purposes of comparing measured or calculated value(s) with specified limits, the measured or calculated value(s) shall be rounded to the nearest decimal or significant digits in the specified limits. 1.3.2 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user's objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analytical methods for engineering design. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||
|
Historická
1.7.2012
Historická
1.11.2013
Historická
15.1.2013
Historická
15.1.2013
Historická
1.7.2006
Historická
1.6.2014
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 22.12.2024 (Počet položek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.