Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D2161-17
Standard Practice for Conversion of Kinematic Viscosity to Saybolt Universal Viscosity or to Saybolt Furol Viscosity
Přeložit název
NORMA vydána dne 1.7.2017
Informace o normě:
Označení normy: ASTM D2161-17
Poznámka: NEPLATNÁ
Datum vydání normy: 1.7.2017
Kód zboží: NS-688040
Počet stran: 25
Přibližná hmotnost: 75 g (0.17 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D2161-17 :
Keywords:
kinematic viscosity, Saybolt furol, Saybolt universal,, ICS Number Code 17.060 (Measurement of volume, mass, density, viscosity)
Doplňující informace
| Significance and Use | ||||||
|
4.1 At one time the petroleum industry relied on measuring kinematic viscosity by means of the Saybolt viscometer, and expressing kinematic viscosity in units of Saybolt Universal Seconds (SUS) and Saybolt Furol Seconds (SFS). This practice is now obsolete in the petroleum industry. 4.2 This practice establishes the official equations relating SUS and SFS to the SI kinematic viscosity units, mm2/s. 4.3 This practice allows for the conversion between SUS and SFS units and SI units of kinematic viscosity. |
||||||
| 1. Scope | ||||||
|
1.1 This practice2 covers the conversion tables and equations for converting kinematic viscosity in mm2/s at any temperature to Saybolt Universal viscosity in Saybolt Universal seconds (SUS) at the same temperature and for converting kinematic viscosity in mm2/s at 122 °F and 210 °F (50 °C and 98.9 °C) to Saybolt Furol viscosity in Saybolt Furol seconds (SFS) at the same temperatures. Kinematic viscosity values are based on water being 1.0034 mm2/s (cSt) at 68 °F (20 °C). Note 1: A fundamental and preferred method for measuring
kinematic viscosity is by use of kinematic viscometers as outlined
in Test Method D445.
Kinematic viscosity results from Test Method D7042 may be used provided they are
bias-corrected by the application of the correction described in
Test Method D7042 for the
specific sample type. In case of dispute, Test Method D445 shall be the referee method. It is
recommended that kinematic viscosity be reported in millimetres
squared per second, instead of Saybolt Universal Seconds (SUS) or
Saybolt Furol Seconds (SFS). This method is being retained for the
purpose of calculation of kinematic viscosities from SUS and SFS
data that appear in past literature. One millimetre squared per
second (mm2/s) equals one centistoke (cSt), which is
another unit commonly found in older literature.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for reference information purposes only. The SI unit of kinematic viscosity is mm2/s. 1.2.1 Exception—Fahrenheit temperature units are used in this practice because they are accepted by industry for the type of legacy conversions described in this practice. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||
| 2. Referenced Documents | ||||||
|
Doporučujeme:
