Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Polyethylene Upright Storage Tanks
Automaticky přeložený název:
Standardní specifikace pro polyetylénové Vzpřímené skladovacích zásobníků
NORMA vydána dne 15.9.2015
Označení normy: ASTM D1998-15
Poznámka: NEPLATNÁ
Datum vydání normy: 15.9.2015
Kód zboží: NS-619402
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
polyethylene, tanks, upright ,, ICS Number Code 23.020.10 (Stationary containers and tanks)
1. Scope | ||||||||||||||||||||||||
1.1 This specification covers flat-bottom, upright, cylindrical tanks molded in one-piece seamless construction by rotational molding. The tanks are molded from polyethylene for above ground, vertical installation and are capable of containing aggressive chemicals at atmospheric pressure. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship and appearance. Tank capacities are from 1900 L (500 gal) up. 1.2 This specification covers the design of stationery vessels for use at atmospheric pressure intended for use with liquids heated below their flash points and continuous service temperatures below 66°C (150°F) for Type I tanks and below 60°C (140°F) for Type II tanks. 1.2.1 NFPA Standards 30 and NFPA 31 shall be consulted for installations that are subject to the requirements of these standards. 1.3 For service requirements beyond the scope of this specification (1.2), such as externally imposed mechanical forces, internal pressure or vacuum, higher temperature service, etc., other relevant sources of standards, for example, local and state building codes, NFPA, ASME, ARM, etc., shall be consulted. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Note 1: ISO 13341:2005+A1:2011 and ISO 13575:2012 are similar,
but not equivalent to this standard.
1.5 The following precautionary caveat pertains only
to the test methods portion, Section 11, of this specification:
Standard Practice for Conditioning
Plastics for Testing 31 Installation of Oil Burning Equipment 29 CFR 1910.106 Occupational Safety and Health
Administration, Flammable and Combustible Liquids Available from
Occupational Safety and Health Administration (OSHA), 200
Constitution Ave., NW, Washington, DC 20210. Standard Practice for Packaging/Packing
of Plastics Standard Practice for Compression Molding
Thermoplastic Materials into Test Specimens, Plaques, or Sheets Standard Practice for Conducting an
Interlaboratory Study to Determine the Precision of a Test
Method Standard Test Method for Obtaining
Hydrostatic Design Basis for Thermoplastic Pipe Materials or
Pressure Design Basis for Thermoplastic Pipe Products Standard Test Method for Environmental
Stress-Cracking of Ethylene Plastics Standard Terminology Relating to
Plastics Standard Terminology Relating to Plastic
Piping Systems |
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 29.04.2024 (Počet položek: 2 896 215)
© Copyright 2024 NORMSERVIS s.r.o.