Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D1693-13
Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
Automaticky přeložený název:
Standardní zkušební metoda pro environmentální stres-praskání ethylenu plastů
NORMA vydána dne 1.4.2013
Informace o normě:
Označení normy: ASTM D1693-13
Poznámka: NEPLATNÁ
Datum vydání normy: 1.4.2013
Kód zboží: NS-18101
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM D1693-13 :
Keywords:
environmental resistance, polyethylene, stress-cracking, ICS Number Code 83.080.20 (Thermoplastic materials)
Doplňující informace
| Significance and Use | ||||||
|
5.1 This test method may be used for routine inspection purposes by subjecting a required number of specimens to the test conditions for a specified time and noting the number that fail. The cracking obtained with the test reagent is indicative of what may be expected from a wide variety of surface-active agents, soaps, and organic substances that are not absorbed appreciably by the polymer. 5.2 Environmental stress-cracking is a property that is highly dependent upon the nature and level of the stresses applied and on the thermal history of the specimen Condition |
Specimen Thickness |
Notch Depth |
Bath Temperature, °C |
|||
|
mmA |
in. |
mmA |
in. |
|||
|
AB |
min |
3.00 |
0.120 |
0.50 |
0.020 |
50 |
|
|
max |
3.30 |
0.130 |
0.65 |
0.025 |
|
|
BB |
min |
1.84 |
0.0725 |
0.30 |
0.012 |
50 |
|
|
max |
1.97 |
0.0775 |
0.40 |
0.015 |
|
|
CC |
min |
1.84 |
0.0725 |
0.30 |
0.012 |
100C |
|
|
max |
1.97 |
0.0775 |
0.40 |
0.015 |
|
5.3 Information from this test
method is not intended to be used for direct application to
engineering problems.
1.1 This test method covers the
determination of the susceptibility of ethylene plastics, as
defined in Terminology D883, to environmental stress-cracking when
subjected to the conditions herein specified. Under certain
conditions of stress and in the presence of environments such as
soaps, wetting agents, oils, or detergents, ethylene plastics may
exhibit mechanical failure by cracking.
1.2 The values stated in SI units are to be regarded as standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
Standard Specification for Polyethylene Plastics Molding and Extrusion Materials (Includes all amendments and changes 11/17/2022).
Standard Practice for Conditioning Plastics for Testing
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
Standard Terminology Relating to Plastics
Apparatus Drawings and Blueprints Detail drawings of the apparatus are available from ASTM Headquarters. Request and .
Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
Doporučujeme:
Poslední aktualizace: 21.12.2024 (Počet položek: 2 216 840)
© Copyright 2024 NORMSERVIS s.r.o.
Cookies
Cookie - Nastavení 
Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.