Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
Přeložit název
NORMA vydána dne 15.3.2022
Označení normy: ASTM D1430-22
Datum vydání normy: 15.3.2022
Kód zboží: NS-1051681
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
This classification system covers polychlorotrifluoroethylene (PCTFE) plastics that consist of at least 90% chlorotrifluoroethylene and are suitable for extrusion and for compression and injection molding. The remaining 10% may include chemical modifications, such as co-monomers, but not colorants, fillers, plasticizers, or mechanical blends with other resins. PCTFE materials in powders and pellets are classified into one group. The group is subdivided into classes based on chemical composition: Class 1; Class 2; and Class 3. These classes are subdivided into grades: Grades 1, 2, 3, and 0; Grades 1, 2, and 0; and Grades 1, 2, and 0; respectively. The molding or extrusion material shall be of uniform composition and so compounded as to conform to the requirements of this classification system. The properties shall be determined in accordance with the following test methods: conditioning; zero strength time; test conditions; deformation under load; melting point; dissipation factor and dielectric constant; and specific gravity.
Keywords:
fluoropolymers, PCTFE, polychlorotrifluoroethylene, zero strength time,, ICS Number Code 83.080.20 (Thermoplastic materials)
1. Scope | ||||||||||||||||||||||||||||||
1.1?This classification system covers polychlorotrifluoroethylene (PCTFE) plastics that consist of at least 90 % chlorotrifluoroethylene and are suitable for extrusion and for compression and injection molding. Additional components allow for chemical modifications, such as co-monomers, but not colorants, fillers, plasticizers, or mechanical blends with other resins. This classification system does not cover recycled PCTFE materials. 1.2?The physical and electrical properties of parts molded or extruded from PCTFE molding compounds vary with the crystalline content obtained during processing and subsequent annealing. Accordingly, the numerical values listed in Table 1 apply only to the test specimens molded in accordance with Section 8. These values are not applicable as design criteria to semi-finished and finished parts prepared and annealed under other conditions. 1.3?The values stated in SI units as detailed in IEEE/SI-10 are to be regarded as the standard. The values given in parentheses are for information only. 1.4?The following precautionary statement pertains only to the test methods portion, Section 10, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1:?Although this classification system and ISO 20568-1
and ISO 20568-2 differ in approach or detail, data obtained using
either are technically equivalent.
1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||
|
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 21.11.2024 (Počet položek: 2 206 478)
© Copyright 2024 NORMSERVIS s.r.o.