Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method of Sampling and Testing Staple Length of Grease Wool (Withdrawn 2022)
Automaticky přeložený název:
Standardní zkušební metoda pro odběr vzorků a testování Staple Délka Grease vlny
NORMA vydána dne 1.7.2013
Označení normy: ASTM D1234-13
Poznámka: NEPLATNÁ
Datum vydání normy: 1.7.2013
Kód zboží: NS-16710
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
length, sampling, statistics, wool, ICS Number Code 59.060.10 (Natural fibres)
Significance and Use | ||||||||||
5.1 The testing procedure in this test method for the determination of staple length is considered satisfactory for acceptance testing of commercial shipments of grease wool since the test method has been used in the trade for acceptance testing. 5.1.1 In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results in the light of the known bias. 5.2 The test method is used for the determination of the average unstretched staple length and the staple length distribution of a lot of wool in order to assign length classes when determining the conformance of lots and shipments to length specifications. 5.3 In this test method, the size of a lot covered by the test procedure is limited to not more than 200 packages per test. Any shipment exceeding the above limits is divided into lots within the prescribed limits. 5.4 The nature of the sampling procedure is such that grease wool staples as originally drawn from the wool of the lot require only a slight amount of preparation before measurement. The bulk and laboratory samples are synonymous in this test method. 5.5 Compression of wool in the bale makes it difficult to penetrate the interior of the bale with the sampling tool. However, staples can be drawn from the surface of the bale with the sampling tool or by hand. 5.6 Practice D4271 contains information on how to write a section on sampling in test methods. 1.1 This test method2 covers
procedures for sampling and measuring the unstretched staple
length, and variability in length, of grease or pulled wool
staples. The test method is also applicable to mohair and other
animal fibers in staple form. The procedure is not recommended for
individual fibers or groups of straightened fibers.
1.2 The values stated in inch-pound
units are to be regarded as standard. The values given in
parentheses are mathematical conversions to SI units that are
provided for information only and are not considered standard.
1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||
2. Referenced Documents | ||||||||||
|
Historická
1.7.2009
Historická
1.6.2010
Historická
1.7.2013
Historická
1.6.2010
Historická
1.6.2010
Historická
1.12.2012
Poslední aktualizace: 01.11.2024 (Počet položek: 2 208 817)
© Copyright 2024 NORMSERVIS s.r.o.