Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

NEPLATNÁ ASTM C928/C928M-13 15.12.2013 náhled

Doplňující informace

ASTM C928/C928M-13

Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs

Automaticky přeložený název:

Standardní specifikace pro Balíčkové, suché, Rapid-kalení cementové materiály pro beton opravy

NORMA vydána dne 15.12.2013

Jazyk
Provedení	PDF - okamžité stažení - 2 005.90 Kč Tištěné - 2 005.90 Kč
Dostupnost	SKLADEM
Cena	2005.90 Kč bez DPH
2 005.90 Kč

Informace o normě:

Označení normy: ASTM C928/C928M-13
Poznámka: NEPLATNÁ
Datum vydání normy: 15.12.2013
Kód zboží: NS-15697
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Beton. Betonové prefabrikáty

Anotace textu normy ASTM C928/C928M-13 :

Keywords:

cementitious mortar or concrete materials for repair, concrete, packaged, mortar, packaged, packaged dry materials for concrete repair, rapid hardening materials, repair materials, ICS Number Code 91.100.30 (Concrete and concrete products)

Doplňující informace

1. Scope

1.1 This specification covers packaged, dry, cementitious mortar or concrete materials for rapid repairs to hardened hydraulic-cement concrete pavements and structures. Materials that contain organic compounds, such as bitumens, epoxy resins, and polymers, as the principal binder are not included.

1.1.1 Packaged, dry, concrete material contains aggregate of which at least 5 % by mass of the total mixture is retained on a 9.5-mm [³/₈-in.] sieve.

1.1.2 Packaged, dry, mortar material contains aggregate of which less than 5 % by mass of the total mixture is retained on a 9.5-mm [³/₈-in.] sieve.

1.2 Aqueous solutions, aqueous emulsions or dispersions may be included as components of the packaged materials. The manufacturer may specify that these liquids are to replace some or all of the mixing water.

1.3 Aggregates must be included as a component of the packaged materials. The manufacturer may recommend job site addition of specific amounts and types of additional aggregates to his product for some uses. However, such reformulated products are not within the scope of this specification.

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following safety hazards caveat pertains to the test methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

C125-21a	Standard Terminology Relating to Concrete and Concrete Aggregates (Includes all amendments and changes 10/14/2021).
E96/E96M-23	Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
C157/C157M-17	Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete
C39/C39M-23	Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
C78-09	Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)
C109/C109M-23	Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 50?mm [2 in.] Cube Specimens)
C403/C403M-23	Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance
C494/C494M-19e1	Standard Specification for Chemical Admixtures for Concrete (Includes all amendments and changes 8/11/2022).
C666-C666M-15	Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing (Withdrawn 2024)
C672-C672M-12	Standard Test Method for Scaling Resistance of Concrete Surfaces Exposed to Deicing Chemicals (Withdrawn 2021)
C702-98	Standard Practice for Reducing Samples of Aggregate to Testing Size
C778-21	Standard Specification for Standard Sand
C192/C192M-19	Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory
C670-24a	Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials (Includes all amendments and changes 3/11/2024).
C882-05	Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete By Slant Shear
C1012-04	Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
C143/C143M-20	Standard Test Method for Slump of Hydraulic-Cement Concrete