Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Methods for Chemical, Mass Spectrometric, and Spectrochemical Analysis of Nuclear-Grade Uranium Dioxide Powders and Pellets
Automaticky přeložený název:
Standardní zkušební metody pro chemický, hmotnostní spektrometrie a spectrochemical analýza jaderných uranu uhličitého prášků a pelet
NORMA vydána dne 1.9.2011
Označení normy: ASTM C696-11
Poznámka: NEPLATNÁ
Datum vydání normy: 1.9.2011
Kód zboží: NS-14644
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
impurity content, isotopic composition, stoichiometry, uranium content, uranium dioxide: Carbon content--nuclear materials, Chemical analysis--nuclear materials, Atomic ratio--uranium dioxide (powders and pellets), Chlorine content--nuclear materials/applications, Fluoride content, Fluorine content, Gases--radioactive, Dichromate titration, Hydrogen content--nuclear materials, Ferrous sulfate reduction, Ignition--rubber/cellular materials, Ignition impurity correction method
Significance and Use | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Uranium dioxide is used as a nuclear-reactor fuel. In order to be suitable for this purpose, the material must meet certain criteria for uranium content, stoichiometry, isotopic composition, and impurity content. These test methods are designed to show whether or not a given material meets the specifications for these items as described in Specifications C753 and C776. An assay is performed to determine whether the material has the minimum uranium content specified on a dry weight basis. The stoichiometry of the oxide is useful for predicting its sintering behavior in the pellet production process. Determination of the isotopic content of the uranium in the uranium dioxide powder is made to establish whether the effective fissile content is in compliance with the purchaser's specifications. Impurity content is determined to ensure that the maximum concentration limit of certain impurity elements is not exceeded. Determination of impurities is also required for calculation of the equivalent boron content (EBC). |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1. Scope | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1.1 These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade uranium dioxide powders and pellets to determine compliance with specifications. 1.2 The analytical procedures appear in the following order:
7.1 This test method covers the determination of moisture in uranium dioxide samples. Detection limits are as low as 10 μg. 15.1 This test method covers the determination of nitride nitrogen in uranium dioxide in the range from 10 to 250 μg. 23.1 This test method covers the spectrographic analysis of nuclear-grade UO2 for the 26 elements in the ranges indicated in Table 1. 23.2 For simultaneous determination of trace elements by plasma emission spectroscopy refer to Test Method C761. TABLE 1 Recommended Analytical Spectral
Lines and Concentration Range of Trace Elements
A All of the above lines are photographed in the second order, except barium and calcium which are first order lines. B A gallium oxide carrier must be used for silver. See Test Method E402. 31.1 This test method covers the spectrochemical determination of silver in nuclear-grade uranium dioxide. The relative standard deviation is 15 % for the concentration range of 0.1 to 50 μg/g. 33.1 This procedure is designed for a rapid determination of surface area of nuclear-grade uranium dioxide (UO2) powders. The determination of surface area by this procedure is automatic, simple, and fast enough to be used in quality control work. The range of analysis is from 1 to 1500 m2/g. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 02.05.2024 (Počet položek: 2 896 910)
© Copyright 2024 NORMSERVIS s.r.o.