Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM C685/C685M-14
Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing
Automaticky přeložený název:
Standardní specifikace pro beton Made objemovým dávkovací a za stálého mícháníNORMA vydána dne 15.12.2014
Informace o normě:
Označení normy: ASTM C685/C685M-14
Poznámka: NEPLATNÁ
Datum vydání normy: 15.12.2014
Kód zboží: NS-581724
Počet stran: 9
Přibližná hmotnost: 27 g (0.06 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM C685/C685M-14 :
Keywords:
ready-mixed concrete, testing,, ICS Number Code 91.100.30 (Concrete and concrete products)
Doplňující informace
| Significance and Use | |
| A1.2 Significance and Use
A1.2.1 These tests and requirements are used to evaluate loading and operating procedures; verify the accuracy of proportioning and indicating systems; and determine if mixing uniformity has been degraded by excessive wear or by accumulations of hardened concrete, or both (Note A1.1). Note A1.1: The method of loading the batching-mixing unit, proper
maintenance, and other factors may have an effect on the ability of
the unit to produce uniformly mixed concrete. For this reason, the
use of this test method not only measures the efficiency of the
mixer, but also the combined effect of the method of loading and
operating the unit.
A1.2.2 This annex provides additional procedures and cautions that are necessary in the application of existing test methods and practices when used to determine the uniformity of freshly mixed concrete. |
|
| 1. Scope | |
|
1.1 This specification covers concrete made from materials continuously batched by volume, mixed in a continuous mixer, and delivered to the purchaser in a freshly mixed and unhardened state as hereinafter specified. Requirements for quality of concrete shall be either as hereinafter specified or as specified by the purchaser. When the requirements of the purchaser differ from this specification, the purchaser's specification shall govern. This specification does not cover the placement, consolidation, finishing, curing, or protection of the concrete after delivery to the purchaser. Tests and criteria for batching accuracy and mixing efficiency are specified herein. 1.2 The values stated in either SI units, shown in brackets, or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.4 This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ( | |
|
Standard Specification for Slag Cement for Use in Concrete and Mortars |
|
|
Standard Specification for Chemical Admixtures for Use in Producing Flowing Concrete |
|
|
Standard Specification for Aggregates for Radiation-Shielding Concrete |
|
|
Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete (Includes all amendments and changes 3/21/2023). |
|
|
Standard Specification for Blended Hydraulic Cements |
|
|
Standard Test Method for Determining Density of Structural Lightweight Concrete |
|
|
Standard Specification for Chemical Admixtures for Concrete (Includes all amendments and changes 8/11/2022). |
|
|
Standard Specification for Lightweight Aggregates for Structural Concrete |
|
|
Standard Performance Specification for Hydraulic Cement |
|
|
Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
|
|
Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete |
|
|
Standard Specification for Air-Entraining Admixtures for Concrete |
|
|
Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method |
|
|
Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
|
|
Standard Practice for Making and Curing Concrete Test Specimens in the Field |
|
|
Standard Specification for Portland Cement |
|
|
Standard Test Method for Slump of Hydraulic-Cement Concrete |
|
|
Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete |
|
|
Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates |
|
|
Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate (Withdrawn 2024) |
|
|
Standard Terminology Relating to Concrete and Concrete Aggregates (Includes all amendments and changes 10/14/2021). |
|
|
Standard Specification for Ready-Mixed Concrete |
|
|
Standard Specification for Concrete Aggregates |
|
|
Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens |
|
|
Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete |
|
|
Standard Specification for Silica Fume Used in Cementitious Mixtures |
Doporučujeme:
Poslední aktualizace: 24.06.2025 (Počet položek: 2 631 472)
© Copyright 2025 NORMSERVIS s.r.o.
Cookies
Cookie - Nastavení 
Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.
