Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

NEPLATNÁ ASTM C240-08(2012) 1.9.2012 náhled

Doplňující informace

ASTM C240-08(2012)

Standard Test Methods of Testing Cellular Glass Insulation Block

Automaticky přeložený název:

Standardní testovací metody zkoušení pěnového skla Izolační Block

NORMA vydána dne 1.9.2012

Jazyk
Provedení	PDF - okamžité stažení - 1 776.60 Kč Tištěné - 1 776.60 Kč
Dostupnost	SKLADEM
Cena	1 776.60 Kč bez DPH
1 776.60 Kč

Informace o normě:

Označení normy: ASTM C240-08(2012)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.9.2012
Kód zboží: NS-12687
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Tepelně a zvukově izolační materiály

Anotace textu normy ASTM C240-08(2012) :

Keywords:

breaking load, breaking strength, cellular materials, compressive strength, flexural strength, thermal insulating materials-glass, water absorption, ICS Number Code 91.100.60 (Thermal and sound insulating materials)

Doplňující informace

Significance and Use

4.1 From a general standpoint, these test methods outline the particular points which have to be taken into account when applying ASTM standard test methods to the case of cellular glass insulating block.

1. Scope

1.1 These test methods cover the testing of cellular glass insulation block for density, water absorption, compressive strength, flexural strength at ambient temperature; preparation for chemical analysis; and thermal conductivity measurements.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

C168-22	Standard Terminology Relating to Thermal Insulation
C177-19e1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus (Includes all amendments and changes 2/23/2023).
NRC 1.36	Nonmetallic Thermal Insulation for Austenitic Stainless Steel Available from Director of Regulatory Standards, US Atomic Energy Commission, Washington, DC 20545.
MIL-I-24244	Specification Insulation Materials with Special Corrosion, Chloride, and Fluoride Requirements Available from DLA Document Services, Building 4/D, 700 Robbins Ave., Philadelphia, PA 19111-5094, http://quicksearch.dla.mil.
ISO 3951	Sampling Procedure and Charts for Inspection by Variables for Percent Nonconforming Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
D4869/D4869M-16a(2021)	Standard Specification for Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing (Includes all amendments and changes 1/6/2021).
D226/D226M-17(2023)	Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing
C871-18(2023)	Standard Test Methods for Chemical Analysis of Thermal Insulation Materials for Leachable Chloride, Fluoride, Silicate, and Sodium Ions
C518-21	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C390-08(2019)	Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
C165-23	Standard Test Method for Measuring Compressive Properties of Thermal Insulations
C303-21	Standard Test Method for Dimensions and Density of Preformed Block and Board–Type Thermal Insulation
C203-22	Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation