Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM C192/C192M-12a
Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory (Includes all amendments And changes 8/19/2013).
Automaticky přeložený název:
Standardní praxe pro Making a vytvrzování Beton zkušebních vzorků v laboratoři
NORMA vydána dne 1.12.2012
Informace o normě:
Označení normy: ASTM C192/C192M-12a
Poznámka: NEPLATNÁ
Datum vydání normy: 1.12.2012
Kód zboží: NS-12483
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM C192/C192M-12a :
Keywords:
concrete, cylinders, laboratory, prisms, strength testing, ICS Number Code 91.100.30 (Concrete and concrete products)
Doplňující informace
| Significance and Use | ||||||||||||||||||||||||||||||||||||
|
3.1 This practice provides standardized requirements for preparation of materials, mixing concrete, and making and curing concrete test specimens under laboratory conditions. 3.2 If specimen preparation is controlled as stipulated herein, the specimens may be used to develop information for the following purposes: 3.2.1 Mixture proportioning for project concrete, 3.2.2 Evaluation of different mixtures and materials, 3.2.3 Correlation with nondestructive tests, and 3.2.4 Providing specimens for research purposes. 1.1 This practice covers procedures
for making and curing test specimens of concrete in the laboratory
under accurate control of materials and test conditions using
concrete that can be consolidated by rodding or vibration as
described herein.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
Standard Test Method for Slump of
Concrete (Includes all amendments and changes 8/6/2026). Standard Test Method for Density (Unit
Weight), Yield, and Air Content (Gravimetric) of Concrete (Includes
all amendments and changes 8/6/2024). Standard Practice for Capping Cylindrical
Concrete Specimens Standard Test Method for Air Content of
Freshly Mixed Concrete by the Pressure Method Standard Practice for Agencies Testing
Concrete and Concrete Aggregates for Use in Construction and
Criteria for Testing Agency Evaluation (Includes all amendments and
changes 8/17/2026). Standard Test Method for Temperature of
Freshly Mixed Hydraulic-Cement Concrete Standard Test Method for Air Content of
Freshly Mixed Concrete by the Volumetric Method Standard Practice for Sampling Freshly
Mixed Concrete Standard Test Method for Relative Density
(Specific Gravity) and Absorption of Fine Aggregate Standard Test Method for Surface Moisture
in Fine Aggregate Standard Test Method for Relative Density
(Specific Gravity) and Absorption of Coarse Aggregate Standard Terminology Relating to Concrete
and Concrete Aggregates Standard Test Method for Total Evaporable
Moisture Content of Aggregate by Drying Standard Specification for Mixing Rooms,
Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the
Testing of Hydraulic Cements and Concretes Standard Specification for Chemical
Admixtures for Concrete Standard Specification for Molds for
Forming Concrete Test Cylinders Vertically Standard Test Method for Time of Setting
of Concrete Mixtures by Penetration Resistance Standard Specification for Lightweight
Aggregates for Structural Concrete |
Doporučujeme:
