Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM C1812/C1812M-15e1
Standard Practice for Design of Journal Bearing Supports to be Used in Fiber Reinforced Concrete Beam Tests (Includes all amendments And changes 1/10/2023).
Přeložit název
NORMA vydána dne 1.7.2015
Informace o normě:
Označení normy: ASTM C1812/C1812M-15e1
Poznámka: NEPLATNÁ
Datum vydání normy: 1.7.2015
Kód zboží: NS-639890
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM C1812/C1812M-15e1 :
Keywords:
fiber-reinforced concrete, flexural performance, friction, post-crack, residual strength, roller supports,, ICS Number Code 91.100.30 (Concrete and concrete products)
Doplňující informace
| Significance and Use | ||||||||||
|
4.1 The presence of friction in the supporting rollers used when testing a fiber-reinforced concrete beam will increase the apparent load resistance of the beam. Roller supports designed in accordance with this practice will provide a relatively low and consistent value of friction at the supports. 4.2 Two types of rollers are used to support a beam. One includes a cylindrical bearing that allows the roller assembly to rotate along an axis parallel to the longitudinal axis of the beam and thereby accommodate any warping introduced during specimen fabrication. The other roller does not include the cylindrical bearing. 4.3 The rollers are designed for use with 150 mm [6 in.] or 100 mm [4 in.] deep beams of square cross-section. 4.4 A method is provided for correcting the apparent load resistance measured using the roller with a known value of the effective coefficient of friction of the roller supports to obtain an estimate of the load resistance in the absence of friction. |
||||||||||
| 1. Scope | ||||||||||
|
1.1 This practice prescribes the design of journal-bearing type rollers to support each end of fiber-reinforced concrete beams tested using Test Method C1399/C1399M or Test Method C1609/C1609M. The roller design is intended to provide a consistent and relatively low value of effective coefficient of friction at the beam supports. The bearing design incorporates metal-on-metal sliding surfaces lubricated with grease. Note 1: During the progress of a test, a crack or cracks open
on the underside of the beam between the loaded third points
causing the underside of each portion of the beam to move away from
the center. The design is intended to provide for unlimited
rotation of the roller at the point of contact with the test beam
in response to this motion.
Note 2: The design of the supporting rollers is a significant
factor in determining the magnitude of the arching forces that
cause error in flexural test results.2
Improperly designed supporting rollers can influence the apparent
flexural behavior of fiber-reinforced concrete beams.3
The effective coefficient of friction can be determined using a
method similar to that described by Bernard.4
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||
| 2. Referenced Documents | ||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
