Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Guide for Dry Lead Glass and Oil-Filled Lead Glass Radiation Shielding Window Components for Remotely Operated Facilities
Automaticky přeložený název:
Standardní příručka pro Dry olovnatého skla a olejové olovnatého skla Radiation stínění oken Komponenty pro dálkově ovládaná zařízení
NORMA vydána dne 1.11.2010
Označení normy: ASTM C1572-10
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2010
Kód zboží: NS-11885
Počet stran: 32
Přibližná hmotnost: 96 g (0.21 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
barrier shield, dielectric discharge, dry lead glass window, hot cell, installation/extraction table/device, installation and maintenance, oil-filled lead glass window, shielding glass, shielding oil, shielding plug, shielding window, view port, wall liner embedment, Barrier shield glass, Dry lead glass, OiI-filled lead glass, Radiation shielding, Remotely-operated facilities, S shielding wall plugs, Wall liner embedments, Windows/window assemblies, ICS Number Code 13.280 (Radiation protection)
Significance and Use | ||||||||||||||||||||||||||||
Radiation Shielding Window Components: Radiation shielding window components operability and long-term integrity are concerns that originate during the design and fabrication sequences. Such concerns can only be addressed, or are most efficiently addressed, during one or the other of these stages. The operability and integrity can be compromised during handling and installation sequences. For this reason, the subject equipment should be handled and installed under closely controlled and supervised conditions. This standard is intended as a supplement to other standards and to federal and state regulations, codes, and criteria applicable to the design of radiation shielding window components. |
||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||
1.1 Intent: 1.1.1 The intent of this standard is to provide guidance for the design, fabrication, quality assurance, inspection, testing, packaging, shipping, installation, and maintenance of radiation shielding window components. These window components include wall liner embedments, dry lead glass radiation shielding window assemblies, oil-filled lead glass radiation shielding window assemblies, shielding wall plugs, barrier shields, view ports, and the installation/extraction table/device required for the installation and removal of the window components. 1.2 Applicability: 1.2.1 This standard is intended for those persons who are tasked with the planning, design, procurement, fabrication, installation, and operation of the radiation shielding window components that may be used in the operation of hot cells, high level caves, mini-cells, canyon facilities, and very high level radiation areas. 1.2.2 This standard applies to radiation shielding window assemblies used in normal concrete walls, high-density concrete walls, steel walls and lead walls. 1.2.3 The system of units employed in this standard is the metric unit, also known as SI Units, which are commonly used for International Systems, and defined, by Standard for Use of International System of Units. Common nomenclature for specifying some terms; specifically shielding, uses a combination of metric units and inch-pound units. |
||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||
|
Historická
1.6.2010
Historická
1.6.2014
Historická
1.6.2014
Historická
1.6.2013
Historická
1.5.2014
Historická
1.1.2008
Poslední aktualizace: 23.12.2024 (Počet položek: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.