ASTM D5050-08
ASTM D5860-95(2013)..
ASTM D5982-07
ASTM D6023-07
ASTM D6154-09
ASTM D6449-99(2008)..
Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM C1439-13
Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar
Automaticky přeložený název:
Standardní zkušební metody pro hodnocení Latex a prášek Polymerní modifikátory pro použití v hydraulických cementárna betonu a malty
NORMA vydána dne 1.10.2013
Informace o normě:
Označení normy: ASTM C1439-13
Poznámka: NEPLATNÁ
Datum vydání normy: 1.10.2013
Kód zboží: NS-11290
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM C1439-13 :
Keywords:
latex, latex polymer, polymer-modified concrete, polymer-modified mortar, powder polymer, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
Doplňující informace
| Significance and Use | ||||||||||||||||||||||||||||||||||||||||||
|
3.1 These test methods are used to develop data for comparison with the requirements of Specification C1438. Standardized procedures are used to compare the properties of specimens made from test mixtures of polymer-modified concrete or mortar with the properties of specimens made from reference mixtures. These test methods are not intended to simulate job conditions. |
||||||||||||||||||||||||||||||||||||||||||
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||
|
1.1 These test methods provide a means of determining the effect of adding polymer modifiers to reference concrete or mortar. 1.2 Most sections of ASTM test methods and practices for hydraulic cement mortar and concrete apply to the preparation and testing of specimens made with polymer-modifiers. However, there are some exceptions, most notably curing, that need special procedures in order to develop the properties inherent with polymer-modification. These test methods cover these exceptions. 1.3 For testing polymer-modified mortar and concrete specimens, the procedures in this standard supersede those in the referenced ASTM test methods and practices. These test methods are not applicable to dry, packaged mortar and concrete. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
Standard Specification for Concrete
Aggregates Standard Test Method for Relative Density
(Specific Gravity) and Absorption of Coarse Aggregate (Withdrawn
2024) Standard Test Method for Relative Density
(Specific Gravity) and Absorption of Fine Aggregate Standard Specification for Portland
Cement Standard Practice for Making and Curing
Concrete Test Specimens in the Laboratory Standard Specification for Air-Entraining
Admixtures for Concrete Standard Test Method for Time of Setting
of Concrete Mixtures by Penetration Resistance Standard Specification for Standard
Sand Standard Test Method for Flow of
Hydraulic Cement Mortar Standard Practice for Mechanical Mixing
of Hydraulic Cement Pastes and Mortars of Plastic Consistency Standard Specification for Chemical
Admixtures for Concrete (Includes all amendments and changes
8/11/2022). Standard Test Method for Electrical
Indication of Concrete’s Ability to Resist Chloride Ion Penetration
(Includes all amendments and changes 6/27/2022). Standard Test Method for Bond Strength of
Adhesive Systems Used with Concrete as Measured by Direct
Tension Standard Specification for Latex and
Powder Polymer Modifiers for use in Hydraulic Cement Concrete and
Mortar Standard Test Method for Compressive
Strength of Cylindrical Concrete Specimens Standard Test Method for Compressive
Strength of Hydraulic Cement Mortars (Using 50?mm [2 in.] Cube
Specimens) Standard Test Method for Density (Unit
Weight), Yield, and Air Content (Gravimetric) of Concrete Standard Test Method for Slump of
Hydraulic-Cement Concrete Standard Test Method for Air Content of
Freshly Mixed Concrete by the Volumetric Method Standard Test Method for Air Content of
Hydraulic Cement Mortar Standard Test Method for Air Content of
Freshly Mixed Concrete by the Pressure Method |
Podobné normy:
Historická
15.11.2008
Historická
1.6.2013
Historická
1.11.2007
Historická
1.11.2007
Historická
1.6.2009
Historická
1.1.2008
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
