Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM C1393-14

Standard Specification for Perpendicularly Oriented Mineral Fiber Roll and Sheet Thermal Insulation for Pipes and Tanks

Automaticky přeložený název:

Standardní specifikace pro kolmo orientované minerálních vláken Roll a list Tepelná izolace pro trubky a nádrže

NORMA vydána dne 1.1.2014

Jazyk
Provedení	PDF - okamžité stažení - 2 005.90 Kč Tištěné - 2 005.90 Kč
Dostupnost	SKLADEM
Cena	2005.90 Kč bez DPH
2 005.90 Kč

Informace o normě:

Označení normy: ASTM C1393-14
Poznámka: NEPLATNÁ
Datum vydání normy: 1.1.2014
Kód zboží: NS-11003
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Stacionární nádoby a nádrže
Znovuzískávání tepla. Tepelná izolace

Anotace textu normy ASTM C1393-14 :

Keywords:

apparent thermal conductivity, facing, mineral fiber, perpendicularly oriented fiber, pipe and tank insulation, sheet, shot, shot content, ICS Number Code 23.020.10 (Stationary containers and tanks), 27.220 (Heat recovery. Thermal insulation)

Doplňující informace

1. Scope

1.1 This specification covers the composition, dimensions, and physical properties of compression-resistant, perpendicularly oriented mineral fiber (rock, slag, or glass) roll and sheet insulation intended for use on flat, curved, or round surfaces operating at temperatures between 0°F (–18°C) and 1000°F (538°C). This product (pipe and tank insulation) is typically used on nominal 24 in. (610 mm) or greater diameter surfaces. For specific applications, the actual use temperatures and diameters shall be agreed upon between the manufacturer and the purchaser.

1.2 The orientation of the fibers within the roll or sheet insulation is essentially perpendicular to the heated/cooled surface (parallel to heat flow). This specification does not apply to flat block, board, duct wrap, or preformed pipe mineral fiber insulation where the insulation fiber orientation is generally parallel to the heated/cooled surface (across the heat flow).

1.3 For satisfactory performance, properly installed protective vapor retarders must be used in below ambient temperature applications to reduce movement of moisture/water vapor through or around the insulation towards the colder surface. Failure to use a vapor retarder can lead to insulation and system damage. Refer to Practice C921 to aid material selection. Although vapor retarders properties are not part of this specification, properties required in Specification C1136 are pertinent to application or performance.

1.4 When the installation or use of thermal materials, accessories, and systems may pose safety or health problems, the manufacturer shall provide the user-appropriate current information regarding any known problems associated with the recommended use for the products of the company and shall also recommend protective measures to be employed in their safe utilization. The user shall establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

C680-23a	Standard Practice for Estimate of the Heat Gain or Loss and the Surface Temperatures of Insulated Flat, Cylindrical, and Spherical Systems by Use of Computer Programs (Includes all amendments and changes 12/13/2023).
C1045-19	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
C1058-03	Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
C1104/C1104M-19	Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation
C1114-06(2019)	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
C303-21	Standard Test Method for Dimensions and Density of Preformed Block and Board–Type Thermal Insulation
C390-08(2019)	Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
C177-19e1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus (Includes all amendments and changes 2/23/2023).
C921-10	Standard Practice for Determining the Properties of Jacketing Materials for Thermal Insulation
C1136-23	Standard Specification for Flexible, Low Permeance Vapor Retarders for Thermal Insulation
C1335-23	Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation
C1338-19(2022)	Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings
C1617-19	Standard Practice for Quantitative Accelerated Laboratory Evaluation of Extraction Solutions Containing Ions Leached from Thermal Insulation on Aqueous Corrosion of Metals
E84-23d	Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 1/29/2024).
CAN/ULC-S102	Standard Method of Test for Surface Burning Characteristics of Building Materials and Assemblies Available from Underwriters Laboratories (UL), 2600 N.W. Lake Rd., Camas, WA 98607-8542, http://www.ul.com.
C165-23	Standard Test Method for Measuring Compressive Properties of Thermal Insulations
C168-22	Standard Terminology Relating to Thermal Insulation
C411-19	Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
C447-15(2022)	Standard Practice for Estimating the Maximum Use Temperature of Thermal Insulations
C518-21	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C665-23	Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
C795-08(2023)	Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel