Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM C1393-00a(2006)e1
Standard Specification for Perpendicularly Oriented Mineral Fiber Roll and Sheet Thermal Insulation for Pipes and Tanks (Includes all amendments And changes 12/31/2010).
Automaticky přeložený název:
Standardní specifikace pro kolmo orientovaných minerálních vláken Roll a plechu Tepelná izolace pro trubky a nádrže
NORMA vydána dne 1.9.2006
Informace o normě:
Označení normy: ASTM C1393-00a(2006)e1
Poznámka: NEPLATNÁ
Datum vydání normy: 1.9.2006
Kód zboží: NS-10999
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM C1393-00a(2006)e1 :
Keywords:
apparent thermal conductivity, facing, mineral fiber, perpendicularly oriented fiber, pipe and tank insulation, sheet, shot, shot content, Mineral fiber insulation--specifications, Perpendicularly-oriented mineral fiber insulation, Pipe thermal insulation, Roll thermal insulation, Sheet thermal insulation--specifications, Thermal insulating materials--specifications, ICS Number Code 23.020.10 (Stationary containers and tanks), 27.220 (Heat recovery. Thermal insulation)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers the composition, dimensions, and physical properties of compression-resistant, perpendicularly oriented mineral fiber (rock, slag, or glass) roll and sheet insulation intended for use on flat, curved, or round surfaces up to 1000°F (538°C). This product (pipe and tank insulation) is typically used on nominal 24 in. (610 mm) or greater diameter surfaces. For specific applications, the actual use temperatures and diameters shall be agreed upon between the manufacturer and the purchaser. 1.2 The orientation of the fibers within the roll or sheet insulation is essentially perpendicular to the heated/cooled surface (parallel to heat flow). This specification does not apply to flat block, board, duct wrap, or preformed pipe mineral fiber insulation where the insulation fiber orientation is generally parallel to the heated/cooled surface (across the heat flow). 1.3 For satisfactory performance, properly installed protective vapor retarders must be used in low-temperature (below ambient) applications to prevent movement of water vapor through or around the insulation towards the colder surface. 1.4 The values stated in inch-pound units are to be regarded as standard. The SI equivalents of inch-pound units are given in parentheses for information only and may be approximate. 1.5 When the installation or use of thermal materials, accessories, and systems may pose safety or health problems, the manufacturer shall provide the user-appropriate current information regarding any known problems associated with the recommended use of the company's products and shall also recommend protective measures to be employed in their safe utilization. The user shall establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
