Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Determination of the Proportion of Phases in Portland Cement and Portland-Cement Clinker Using X-Ray Powder Diffraction Analysis
Automaticky přeložený název:
Standardní zkušební metoda pro stanovení podílu fází portlandského cementu a Portland-cementový slínek pomocí analýzy X-Ray práškové difrakce
NORMA vydána dne 1.12.2011
Označení normy: ASTM C1365-06(2011)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.12.2011
Kód zboží: NS-10871
Počet stran: 10
Přibližná hmotnost: 30 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
alite, alkali sulfate, aluminate, belite, cement, clinker, diffractometer, ferrite, periclase, phase analysis, quantitative X-ray powder diffraction analysis, QXRD, Rietveld analysis, X-ray powder diffraction, XRD, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
Significance and Use | ||||||||||||||
This test method allows direct determination of the proportion of some individual phases in cement or portland-cement clinker. Thus it provides an alternative to the indirect estimation of phase proportion using the equations in Specification C150 (Annex A1). This test method assumes that the operator is qualified to operate an X-ray diffractometer and to interpret X-ray diffraction spectra. This test method may be used as part of a quality control program in cement manufacturing. This test method may be used in predicting properties and performance of hydrated cement and concrete that are a function of phase composition. QXRD provides a bulk analysis (that is, the weighted average composition of several grams of material). Therefore, results may not agree precisely with results of microscopical methods. |
||||||||||||||
1. Scope | ||||||||||||||
1.1 This test method covers direct determination of the proportion by mass of individual phases in portland cement or portland-cement clinker using quantitative X-ray (QXRD) analysis. The following phases are covered by this standard: alite (tricalcium silicate), belite (dicalcium silicate), aluminate (tricalcium aluminate), ferrite (tetracalcium aluminoferrite), periclase (magnesium oxide), gypsum (calcium sulfate dihydrate), bassanite (calcium sulfate hemihydrate), anhydrite (calcium sulfate), and calcite (calcium carbonate). 1.2 This test method specifies certain general aspects of the analytical procedure, but does not specify detailed aspects. Recommended procedures are described, but not specified. Regardless of the procedure selected, the user shall demonstrate by analysis of certified reference materials (CRM's) that the particular analytical procedure selected for this purpose qualifies (that is, provides acceptable precision and bias) (see Note 1). The recommended procedures are ones used in the round-robin analyses to determine the precision levels of this test method. Note 1—A similar approach was used in the performance requirements for alternative methods for chemical analysis in Test Methods C114. 1.3 The values stated in SI units shall be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards, see Section 9. |
||||||||||||||
2. Referenced Documents | ||||||||||||||
|
Historická
1.8.2014
Historická
1.9.2014
Historická
1.12.2011
Historická
15.11.2013
Historická
1.4.2012
Historická
1.4.2012
Poslední aktualizace: 22.11.2024 (Počet položek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.