Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Nickel-Cobalt Alloy Coating
Přeložit název
NORMA vydána dne 1.5.2022
Označení normy: ASTM B994/B994M-22
Datum vydání normy: 1.5.2022
Kód zboží: NS-1057074
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
alloy, coating, cobalt, corrosion, corrosion in threaded articles, corrosion rate, dismantle, electrochemical testing, metal coating, nickel, nickel-cobalt alloy, performance, protective coating, salt spray (fog) chamber, torque ratio,, ICS Number Code 25.220.40 (Metallic coatings)
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||
1.1?This specification describes the requirements for corrosion-resistant coatings of electrodeposited nickel-cobalt on metallic substrates and electrodeposited nickel-cobalt used for electroforming. Note 1:?The nickel-cobalt alloy is principally deposited as a
coating on steel products. It can also be electrodeposited on iron,
stainless steel, aluminum, titanium, and any other metal
substrate.
Note 2:?The nickel-cobalt alloy coating has a low coefficient
of friction of 0.08 that provides a dry lubricant on part surfaces
that are in contact with each other and are subject to
galling.
1.2?This specification incorporates an accelerated exposure test method to evaluate the effects of corrosion and galling on the coating, and incorporates a means of reporting the results to the purchaser. 1.3?The specification incorporates a classification scheme that establishes service conditions for thickness, classes of deposits based on the level of monitoring, and type based on supplemental coatings used after deposition. 1.4?The coating thickness ranges from 5 to >30 ?m, and it can be applied to machined parts, springs, latches, threaded parts, fasteners, etc. The deposit can also be used to electroform parts requiring high strength with the alloy being maintained at 50 % nickel-cobalt. 1.5?The nickel-cobalt alloy is used to protect ferrous metals in contact with corrosive environments such as: oil and gas production facilities, coastal marine, and ACQ (Alkaline Copper Quaternary) treatments for wood treatments. 1.6?UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8?This standard has been revised to comply with the Restriction of Hazardous Substances 1.9?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 13.09.2024 (Počet položek: 2 429 660)
© Copyright 2024 NORMSERVIS s.r.o.