Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Automated Controlled Shot Peening of Metallic Articles Prior to Nickel, Autocatalytic Nickel, or Chromium Plating, or as Final Finish
Automaticky přeložený název:
Standardní specifikace pro automatizované ovládanou okuličkování kovových předmětů před Nikl, autokatalytické nikl, nebo chromování, nebo jako konečnou povrchovou úpravou
NORMA vydána dne 1.11.2014
Označení normy: ASTM B851-04(2014)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2014
Kód zboží: NS-8411
Počet stran: 9
Přibližná hmotnost: 27 g (0.06 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
peening, shot, shot peening,, ICS Number Code 25.220.40 (Metallic coatings)
Significance and Use | ||||||||||||||||||||||||||||||||||||||||||||
5.1 Shot peening is a process for cold working surfaces by bombarding the product with shot of a solid and spherical nature propelled at a relatively high velocity. In general, shot peening will increase the fatigue life of a product that is subject to bending or torsional stress. It will improve resistance to stress corrosion cracking. It can be used to form parts or correct their shapes. See Appendix X1 for additional information. 5.2 It is essential that the shot peening process parameters be controlled rigidly to ensure repeatability from part to part and lot to lot. 5.3 This specification covers techniques and methods necessary for proper control of the shot peening process. |
||||||||||||||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
1.1 This specification covers the requirements for automated, controlled shot peening of metallic articles prior to electrolytic or autocatalytic deposition of nickel or chromium, or as a final finish, using shot made of cast steel, conditioned cut wire, or ceramic media. The process is applicable to those materials on which test work has shown it to be beneficial within given intensity ranges. It is not suitable for brittle materials. Hand peening and rotary flap peening are excluded specifically. 1.2 Shot peening induces residual compressive stresses in the surface and near-surface layers of metallic articles, controlling or limiting the reduction in fatigue properties that occurs from nickel or chromium plating of the article, or the fatigue properties of unplated articles. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
Historická
1.12.2013
Historická
1.11.2014
Historická
1.4.2010
Historická
1.10.2011
Historická
1.5.2011
Historická
1.5.2012
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 26.04.2024 (Počet položek: 2 896 057)
© Copyright 2024 NORMSERVIS s.r.o.