Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM B793-13
Standard Specification for Zinc Casting Alloy Ingot for Sheet Metal Forming Dies and Plastic Injection Molds
Automaticky přeložený název:
Standardní specifikace pro zinek slitina ingot pro tváření plechů Dies a forem pro vstřikování plastů
NORMA vydána dne 1.2.2013
Informace o normě:
Označení normy: ASTM B793-13
Poznámka: NEPLATNÁ
Datum vydání normy: 1.2.2013
Kód zboží: NS-8149
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM B793-13 :
Keywords:
blanking dies, casting, casting alloys, forming dies, gravity casting, Kirksite, Kirksite A, Kirksite B, sheet metal dies, zinc, ICS Number Code 77.120.60 (Lead, zinc, tin and their alloys)
Doplňující informace
| 1. Scope | ||
|
1.1 This specification covers commercial zinc alloys in ingot form for remelting for the manufacture of dies and molds from the alloys as shown in
|
Composition, % |
|
|
UNS Z35543 |
UNS Z35542 |
|
|
Color CodeC |
Green/Red |
Green/Black |
|
Element |
|
|
|
Aluminum |
3.5–4.5 |
3.9–4.3 |
|
Cadmium |
0.005 max |
0.003 max |
|
Copper |
2.5–3.5 |
2.5–2.9 |
|
Iron |
0.100 max |
0.075 max |
|
Lead |
0.007 max |
0.003 max |
|
Magnesium |
0.02–0.10 |
0.02–0.05 |
|
Tin |
0.005 max |
0.001 max |
|
Zinc |
Remainder |
Remainder |
1.2 This specification presents
requirements for zinc alloys suitable for the production of sand
cast or plaster cast forming dies for sheet metal stamping
operations and plastic injection molding. Alloy A is intended for
use in the fabrication of dies for sheet metal stamping under drop
hammer and hydraulic pressure. Alloy B is a special purpose alloy
of closely controlled composition and is primarily used in the
manufacture of plastic injection molds.
1.3 This specification covers two zinc alloys which are specified and designated as follows:
|
UNS |
ASTM |
Traditional |
|
|
|
|
|
Z35543 |
Alloy A |
Kirksite A |
|
Z35542 |
Alloy B |
Kirksite B |
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
|
ISO3815-1 |
Zinc and zinc alloysPart 1: Analysis of solid samples by optical emission spectrometry |
|
ISO3815-2 |
|
|
Standard Specification for Configuration of Zinc and Zinc Alloy Jumbo, Block, Half Block, and Slab Ingot |
|
|
Standard Test Methods for Chemical Analysis of Zinc and Zinc Alloys |
|
|
Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
|
|
Standard Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition |
|
|
Standard Specification for General Requirements for Zinc and Zinc Alloy Products |
|
|
Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
|
|
Standard Practice for the Use of Color Codes for Zinc Casting Alloy Ingot |
|
|
Standard Terminology Relating to Non-ferrous Metals and Alloys |
Doporučujeme:
