Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM B666/B666M-20
Standard Practice for Identification Marking of Aluminum and Magnesium Products
Přeložit název
NORMA vydána dne 1.11.2020
Informace o normě:
Označení normy: ASTM B666/B666M-20
Datum vydání normy: 1.11.2020
Kód zboží: NS-1010364
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM B666/B666M-20 :
This practice establishes the requirements for physical item identification marking of aluminum and magnesium products. Package marking for shipment and inspection acceptance is not within the scope of this standard. Wrought aluminum and magnesium mill products shall be marked for identification purposes only with the following information on the product or on tags attached to the product: (1) name or registered trademark of the company, (2) alloy and temper of the product, (3) basic number of the specification to which the product was produced, (4) specified (ordered) dimensions of the following products: sheet and plate, coiled wire and spooled wire, straight length tube and coiled tube, and pipe, (5) lot number, and (6) the word ""seamless"" on certain tube or pipe. Spot marking requirements for the following wrought aluminum and magnesium mill products are detailed and illustrated: (1) coiled sheet, (2) flat sheet and plate, (3) circles, (4) tread plate, (5) foil, (6) rod, bar, and extruded profiles, (7) structural profiles, (8) tube and pipe, (9) wire, (10) bus bar, and (11) forgings such as hand and die forgings. Requirements for marking cast aluminum and magnesium products (castings, remelt ingot for castings, and ingot or billet for fabricating), unalloyed aluminum and magnesium ingot, and special products are specified.
Keywords:
aluminum products, identification markings, magnesium products ,, ICS Number Code 77.150.10 (Aluminium products),77.150.99 (Other products of non-ferrous metals)
Doplňující informace
| 1. Scope | ||||||||||||
|
1.1 This practice establishes the physical item marking requirements for identification purposes for aluminum and magnesium products. Package marking for shipment and inspection acceptance is not within the scope of this standard. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
