Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Measurement of Thickness of Transparent or Opaque Coatings by Double-Beam Interference Microscope Technique (Withdrawn 2016)
Automaticky přeložený název:
Standardní zkušební metoda pro měření tloušťky průhledné nebo neprůhledné povlaky Double-Beam Interference mikroskopy Technika
NORMA vydána dne 1.11.2010
Označení normy: ASTM B588-88(2010)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2010
Kód zboží: NS-7298
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
Aluminum coatings, Anodic coatings, Anodic coatings--Al/Al alloys), Chromium electroplating, Coating thickness, Destructive testing--coatings, Double-beam interference microscopy, Electrodeposited coatings, Metallic coatings, Microscopic examination--metallic/inorganic coatings, Opacity/opaque materials, Steel--electrodeposited coatings, Thickness--electrodeposited coatings, Transparent coatings, ICS Number Code 17.040.20 (Properties of surfaces)
Significance and Use | ||
The thickness of a coating is often critical to its performance. For some coating-substrate combinations, the interference microscope method is a reliable method for measuring coating thickness. This test method is suitable for specification acceptance. |
||
1. Scope | ||
1.1 This test method covers the measurement of the thickness of transparent metal oxide and metallic coatings by utilizing a double-beam interference microscope. 1.2 The test method requires that the specimen surface or surfaces be sufficiently mirrorlike to form recognizable fringes. 1.3 This test method can be used nondestructively to measure 1 to 10μ m thick transparent coatings, such as anodic coatings on aluminum. The test method is used destructively for 0.1 to 10 μm thick opaque coatings by stripping a portion of the coating and measuring the step height between the coating and the exposed substrate. The stripping method can also be used to measure 0.2 to 10 μm thick anodic coatings on aluminum. 1.4 The test method is usable as a reference method for the measurement of the thickness of the anodic film on aluminum or of metallic coatings when the technique includes complete stripping of a portion of the coating without attack of the substrate. For anodic films on aluminum, the thickness must be greater than 0.4 μm; the uncertainty can be as great as 0.2 μm. For metallic coatings, the thickness must be greater than 0.25 μm; the uncertainty can be as great as 0.1 μm. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||
2. Referenced Documents | ||
|
Historická
1.5.2014
Historická
1.5.2014
Historická
1.5.2014
Historická
1.5.2014
Historická
1.11.2010
Historická
1.4.2010
Poslední aktualizace: 22.11.2024 (Počet položek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.