Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM B570-22
Standard Specification for Copper-Beryllium Alloy Forgings and Extrusions (UNS Nos. C17000 and C17200)
Přeložit název
NORMA vydána dne 1.10.2022
Informace o normě:
Označení normy: ASTM B570-22
Datum vydání normy: 1.10.2022
Kód zboží: NS-1087618
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM B570-22 :
This specification establishes the requirements for copper-beryllium alloy (UNS nos. C17000 and C17200) forgings and extrusions. The material of manufacture shall be cast or wrought billet of C17000 or C17200 of such purity and soundness as to be suitable for processing into the products prescribed. The product shall be manufactured by hot working and heat treating as may be necessary to meet the properties specified. The product composition shall conform to the chemical requirements specified. The standard temper designations available under this specification and as prescribed in Classification B 601 are solution heat-treated TB00 (A) and precipitation heat-treated TF00 (AT). The product in the TF00 (precipitation-hardened (AT)) condition shall have a microstructure with a minimum of second phase (beta) constituents. When present, beta shall be fine and well dispersed. The product furnished under this specification shall conform to the prescribed hardness requirements. Tensile properties shall be determined in accordance with test methods E 8.
Keywords:
copper beryllium, extrusions, forgings, UNS C17000, UNS C17200 ,, ICS Number Code 77.150.30 (Copper products)
Doplňující informace
| 1. Scope | ||||||||||||||||
|
1.1?This specification establishes the requirements for copper-beryllium alloy forgings and extrusions produced from Copper Alloy UNS Nos. C17000 and C17200. Note 1:?Requirements for copper-beryllium alloy rod and bar
appear in Specification B196/B196M (Section 2).
1.2?Unless otherwise specified, Copper Alloy UNS No. C17200 shall be the alloy furnished whenever Specification B570 is specified without an alloy designation. 1.3?UnitsThe values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4?The following safety hazard caveat pertains only to the test method(s) described in this specification: 1.4.1?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||
|
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
