Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-Nickel-Tin Alloy Sheet and Strip
Přeložit název
NORMA vydána dne 1.10.2022
Označení normy: ASTM B422/B422M-22
Datum vydání normy: 1.10.2022
Kód zboží: NS-1086933
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
This specification establishes the requirements for sheets and strips of copper-aluminum-silicon-cobalt, copper-nickel-silicon-magnesium, copper-nickel-silicon, copper-nickel-aluminum-magnesium, and copper-nickel-tin alloys with Copper Alloy UNS Nos. C19010, C19020, C19025, C63800, C64725, C70250, C70260, and C70265. Materials shall be tested and shall conform to dimensional (thickness, width, length, straightness, and edges), mechanical (tensile and yield strength, elongation, and ductility or formability), electrical resistivity, chemical composition requirements.
Keywords:
copper-aluminum-silicon-cobalt alloy, copper-nickel-aluminum magnesium alloy, copper-nickel-silicon alloy, copper nickel-silicon-magnesium alloy, copper-nickel-tin alloy, sheet, strip, UNS No. C19002, UNS No. C19010, UNS No. C19015, UNS No. C19020, UNS No. C19025, UNS No. C63800, UNS No. C64725, UNS No. C70250, UNS No. C70260, UNS No. C70265, UNS No. C70310, UNS No. C70350,, ICS Number Code 77.150.30 (Copper products)
1. Scope | ||||||||
1.1?This specification establishes the requirements for2 Copper Alloy UNS Nos. C19002, C19010, C19015, C19020, C19025, C63800, C64725, C70250, C70260, C70265, C70310, and C70350 sheet and strip. 1.2?The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3?The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.3.1?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||
2. Referenced Documents | ||||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 09.09.2024 (Počet položek: 2 346 212)
© Copyright 2024 NORMSERVIS s.r.o.