Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM B371/B371M-19
Standard Specification for Copper-Zinc-Silicon Alloy Rod
Přeložit název
NORMA vydána dne 1.4.2019
Informace o normě:
Označení normy: ASTM B371/B371M-19
Datum vydání normy: 1.4.2019
Kód zboží: NS-945890
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM B371/B371M-19 :
This specification establishes the requirements for rods of copper-zinc-silicon alloy with Copper Alloy UNS Nos. C69300, C69400, C69430, C69700, and C69710. The materials for manufacture shall be cast billets, logs, or rods of such purity and soundness as to be suitable for processing by cold working, annealing, straightening, and cutting to length as may be necessary to produce finished products that meet the properties specified. Tempers available under this specification are H02 (half hard) for UNS No. C69300, and H04 (hard) for all other UNS Nos. Products shall be tested (including by residual stress test and ammonia vapor test) and shall adhere to dimensional (diameter, length, straightness, and edge contour), mechanical (tensile and yield strength, and elongation), and chemical composition requirements.
Keywords:
copper-zinc-silicon rod, UNS No. C69240, UNS No. C69300, UNS No. C69400, UNS No. C69410, UNS No. C69430, UNS No. C69700, UNS No. C69710, UNS No. C69850,, ICS Number Code 77.140.60 (Steel bars and rods)
Doplňující informace
| 1. Scope | ||||||||||||||
|
1.1 This specification establishes the requirements for copper-zinc-silicon alloy rod produced in Copper Alloy UNS Nos. C69240, C69300, C69400, C69410, C69430, C69700, C69710, and C69850. 1.1.1 If the purchaser does not specify the alloy to be supplied, product is permitted to be furnished in any of the alloys named in 1.1. 1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.4 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||
| 2. Referenced Documents | ||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
