Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM B283/B283M-22
Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
Přeložit název
NORMA vydána dne 1.10.2022
Informace o normě:
Označení normy: ASTM B283/B283M-22
Datum vydání normy: 1.10.2022
Kód zboží: NS-1087193
Počet stran: 16
Přibližná hmotnost: 48 g (0.11 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM B283/B283M-22 :
This specification establishes the requirements for copper and copper die forgings produced by hot pressing method. The forgings included here are designated with the following Copper or Copper Alloy UNS Nos.: C11000 (copper), C14500 (copper-tellurium alloy), C14700 (copper-sulfur alloy), C36500 (leaded Muntz metal), C37000 (free-cutting Muntz metal), C37700 (forging brass), C46400 (naval brass), C48200 (medium leaded naval brass), C48500 (leaded naval brass), C61900 (aluminum bronze), C62300 (9% aluminum bronze), C63000 and C63200 (aluminum-nickel bronze), C64200 (aluminum-silicon bronze), C64210 (6.7% aluminum-silicon bronze), C65500 (high-silicon bronze), C67500 (manganese bronze), C67600, C69300 (copper-zinc-silicon alloy), C70620 (90% copper-10% nickel alloy), C71520 (70% copper-30% nickel alloy), and C77400 (45% nickel-10% silver alloy). The materials for manufacture shall be rods, billets, or blanks of such purity and soundness as to be suitable for processing by hot pressing. Products shall be tested to examine their conformance to mechanical (tensile and yield strengths, and elongation), dimensional, and chemical composition requirements.
Keywords:
copper and copper alloy die forgings (hot pressed), die forgings (hot pressed), EN 1412 No. CW612N, EN 1412 No. CW617N, UNS No. C11000, UNS No. C14500, UNS No. C14700, UNS No. C27450, UNS No. C27451, UNS No. C27453, UNS No. C28500, UNS No. C35330, UNS No. C36300, UNS No. C36500, UNS No. C37000, UNS No. C37700, UNS No. C46400, UNS No. C46500, UNS No. C46750, UNS No. C48200, UNS No. C48500, UNS No. C48600, UNS No. C48640, UNS No. C48645, UNS No. C49250, UNS No. C49255, UNS No. C49260
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This specification establishes the requirements for copper and copper alloy die forgings produced by the hot pressing method. The following copper and copper alloys are included:
1.2?UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined. Note 1:?Nominal composition and relative forgeability ratings
are given in Appendix X1.
Copper-nickel alloys C70620 and C71520 are intended for welded
applications with seawater exposure.
Note 2:?Guidelines for design and development of forgings are
included in Appendix
X2.
Note 3:?Wrought product intended for hot forging is described
in Specification B124/B124M.
1.3?The following safety caveat pertains only to Section 10 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
