Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

NEPLATNÁ ASTM B103/B103M-15 15.5.2015 náhled

Doplňující informace

ASTM B103/B103M-15

Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

Automaticky přeložený název:

Standardní specifikace pro fosforový bronz Plate , plechy, pásy , a válcované Bar

NORMA vydána dne 15.5.2015

Jazyk
Provedení	PDF - okamžité stažení - 1 771.20 Kč Tištěné - 1 771.20 Kč
Dostupnost	SKLADEM
Cena	1 771.20 Kč bez DPH
1 771.20 Kč

Informace o normě:

Označení normy: ASTM B103/B103M-15
Poznámka: NEPLATNÁ
Datum vydání normy: 15.5.2015
Kód zboží: NS-609032
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Výrobky z mědi

Anotace textu normy ASTM B103/B103M-15 :

Keywords:
copper-tin alloy plate, copper-tin alloy rolled bar, copper-tin alloy sheet, copper-tin alloy strip, copper-tin-lead alloy plate, copper-tin-lead alloy rolled bar, copper-tin-lead alloy sheet, copper-tin-lead alloy strip, copper-tin-lead-zinc alloy plate, copper-tin-lead-zinc alloy rolled bar, copper-tin-lead-zinc alloy sheet, copper-tin-lead-zinc alloy strip, copper-tin-lead-zinc-iron alloy sheet, copper-tin-lead-zinc-iron alloy strip, UNS No. C51000, UNS No. C51100, UNS No. C51180

Doplňující informace

1. Scope

1.1 This specification establishes the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers. The following alloys are covered:

Copper Alloy UNS No.2

Nominal Composition, %

Previously Used Designation

Copper

Tin

Zinc

Lead

C51000

. . .

C51100

. . .

C51180

. . .

C51900

. . .

C52100^A

. . .

C52180

. . .

C52400

. . .

C53400

. . .

C54400

Note 1: All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties.

1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.

1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

E478-08(2017)	Standard Test Methods for Chemical Analysis of Copper Alloys
B248-22	Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
B248M-22	Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)
B601-18a	Standard Classification for Temper Designations for Copper and Copper Alloys´Wrought and Cast (Includes all amendments and changes 10/24/2018).
B846-19a	Standard Terminology for Copper and Copper Alloys (Includes all amendments and changes 8/8/2019).
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E8/E8M-24	Standard Test Methods for Tension Testing of Metallic Materials
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75-76(1996)	Standard Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition

Doporučujeme:

EviZak - všechny zákony včetně jejich evidence na jednom místě

Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !

Chcete vědět více informací? Podívejte se na tuto stránku.