Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Norma ASTM A805/A805M-09(2021) 1.9.2021 náhled

Doplňující informace

ASTM A805/A805M-09(2021)

Standard Specification for Steel, Flat Wire, Carbon, Cold-Rolled

Přeložit název

NORMA vydána dne 1.9.2021

Jazyk
Provedení	PDF - okamžité stažení - 1 592.60 Kč Tištěné - 1 592.60 Kč
Dostupnost	SKLADEM
Cena	1592.60 Kč bez DPH
1 592.60 Kč

Informace o normě:

Označení normy: ASTM A805/A805M-09(2021)
Datum vydání normy: 1.9.2021
Kód zboží: NS-1036729
Počet stran: 13
Přibližná hmotnost: 39 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Ocelové dráty, drátěná lana a článkové řetězy

Anotace textu normy ASTM A805/A805M-09(2021) :

This specification covers carbon steel flat wire in coils or cut lengths. The steel materials shall be produced from rimmed, capped, semi-killed, hot-rolled or cold-rolled steel. The steel specimens shall undergo cast or heat analysis and product analysis and shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, and copper. The desired edge shall be classified as follows: prepared edge of a specified contour produced when a very accurate width is required or when the finish of the edge suitable for electroplating is required, or both (Number 1 Edge); not applicable to flat wire products ( Number 2 Edge); approximately square edge produced by slitting (Number 3 Edge); rounded edge produced either by edge rolling or resulting from flat rolling of a round section (Number 4 Edge); square edge produced from slit-edge material on which the burr is eliminated by rolling or filling (Number 5 Edge); and square edge produced by edge rolling when the width tolerance and edge condition are not as exacting as for No. 1 Edge (Number 6 Edge). The dimensional tolerances shall conform to the required values of thickness, width and length. The steel materials shall conform to the required values of temper, Rockwell hardness and tensile strength.

Keywords:

ICS Number Code 77.140.65 (Steel wire, wir ropes and link chains)

Doplňující informace

1. Scope

1.1?This specification covers carbon steel flat wire in coils or cut lengths. Flat wire is classified as a cold-rolled section, rectangular in shape, 0.500 in. [12.7 mm] or less in width and under 0.250 in. [6.35 mm] in thickness.

1.2?Low-carbon steel flat wire is produced from steel compositions with a maximum carbon content of 0.25 % by cast or heat analysis.

1.3?Carbon spring steel flat wire is produced to a carbon range in which the specified or required maximum is over 0.25 % by cast or heat analysis.

1.3.1?Two types of carbon spring steel flat wire are produced:

1.3.1.1?Untempered cold-rolled carbon spring steel flat wire, produced to several desirable combinations of properties and

1.3.1.2?Hardened and tempered carbon spring steel wire.

1.4?Definite application flat wire is a product developed for a specific application and may be specified only by size and descriptive name.

1.5?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products
E45-18a(2023)	Standard Test Methods for Determining the Inclusion Content of Steel (Includes all amendments and changes 11/6/2023).
A510-08	Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel
A510M-08	Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel [Metric] (Withdrawn 2011)
Recommended Practice SAE J?419	Methods of Measuring Decarburization
E112-13(2021)	Standard Test Methods for Determining Average Grain Size
E140-12B(2019)e1	Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness (Includes all amendments and changes 5/7/2019).
MIL-STD-129
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products

Doporučujeme:

Aktualizace technických norem

Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.

Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.