Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Carbon Steel Forgings for Piping Components with Inherent Notch Toughness
Přeložit název
NORMA vydána dne 1.12.2019
Označení normy: ASTM A727/A727M-14(2019)
Datum vydání normy: 1.12.2019
Kód zboží: NS-978948
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
This specification covers forged carbon steel piping components intended primarily for service in pressure piping systems from a specific temperature range where inherent notch toughness is desired, but where notch toughness testing is not required. Included are forged or ring-rolled flanges, forged fittings, and valves made to specified dimensions. The steel shall be made by one or more of the following processes: open-hearth, basic-oxygen, or electric-furnace, and shall be fully killed, fine-grain practice. Following plastic working, the forgings shall be heat treated by normalizing, or normalizing and tempering, or quenching and tempering. The forgings shall be subjected to tension, hardness, and hydrostatic tests.
Keywords:
carbon equivalent, pipe fittings, steel, piping applications, pressure containing parts, steel flanges, steel forgings, carbon, steel valves, temperature service applications, low,, ICS Number Code 77.140.85 (Iron and steel forgings)
1. Scope | ||||||||
1.1 This specification2 covers forged carbon steel piping components intended primarily for service in pressure piping systems from −20 to +650 °F [−30 to +345 °C] where inherent notch toughness is desired, but where notch toughness testing is not required. Included are forged or ring-rolled flanges, forged fittings, and valves made to specified dimensions, or to dimensional standards such as the ASME and API specifications referenced in Section 2. 1.2 This specification is limited to forgings with maximum finished section thicknesses no larger than 2 in. [51 mm]. 1.3 It shall be the responsibility of the purchaser to determine whether material meeting the requirements of this specification is satisfactory for the service application. 1.4 Supplementary requirements are provided for use when additional testing or inspection is desired. These shall apply only when specified by the purchaser in the order. Note 1: There are no provisions for impact testing in this
specification. When impact testing is required, refer to
Specification A350/A350M.
1.5 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||
2. Referenced Documents | ||||||||
|
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 03.11.2024 (Počet položek: 2 209 203)
© Copyright 2024 NORMSERVIS s.r.o.