Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM A709/A709M-15
Standard Specification for Structural Steel for Bridges
Automaticky přeložený název:
Standardní specifikace pro konstrukční ocel pro mosty
NORMA vydána dne 1.9.2015
Informace o normě:
Označení normy: ASTM A709/A709M-15
Poznámka: NEPLATNÁ
Datum vydání normy: 1.9.2015
Kód zboží: NS-622397
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM A709/A709M-15 :
Keywords:
alloy, atmospheric corrosion resistance, bars, bridges, carbon, fracture-critical, high-strength, low-alloy, non-fracture critical, plates, quenched, shapes, steel, structural steel, tempered,, ICS Number Code 77.140.10 (Heat-treatable steels)
Doplňující informace
| 1. Scope | ||||||||||||||||
|
1.1 This specification covers carbon and high-strength low-alloy steel structural shapes, plates, and bars and quenched and tempered alloy steel for structural plates intended for use in bridges. Seven grades are available in four yield strength levels as follows:
1.1.1 Grades 36 [250], 50 [345], 50S [345S], and 50W [345W] are also included in Specifications A36/A36M, A572/A572M, A992/A992M, and A588/A588M, respectively. When the requirements of Table 9 or Table 10 or the supplementary requirements of this specification are specified, they exceed the requirements of Specifications A36/A36M, A572/A572M, A992/A992M, and A588/A588M. 1.1.2 Grades 50W [345W], HPS 50W [HPS 345W], HPS 70W [HPS 485W], and HPS 100W [HPS 690W] have enhanced atmospheric corrosion resistance (see 13.1.2). Product availability is shown in Table 1. ·
Structural shapes
· Bars · Plates with widths up to and including 15 in. [380 mm] ·
Structural shapes
· Bars · Plates with widths up to and including 15 in. [380 mm] 1.2 Grade HPS 70W [HPS 485W] or HPS 100W
[HPS 690W] shall not be substituted for Grades 36 [250], 50 [345],
50S [345S], 50W [345W], or HPS 50W [HPS 345W]. Grade 50W [345W], or
HPS 50W [HPS 345W] shall not be substituted for Grades 36 [250], 50
[345] or 50S [345S] without agreement between the purchaser and the
supplier.
1.3 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability. 1.4 For structural products to be used as tension components requiring notch toughness testing, standardized requirements are provided in this standard, and they are based upon American Association of State Highway and Transportation Officials (AASHTO) requirements for both fracture critical and non-fracture critical members. 1.5 Supplementary requirements are available but shall apply only if specified in the purchase order. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 For structural products produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply. |
||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||
|
Doporučujeme:
