Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

NEPLATNÁ ASTM A635/A635M-15 1.11.2015 náhled

Doplňující informace

ASTM A635/A635M-15

Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for

Automaticky přeložený název:

Standardní specifikace pro ocel , plechy a pásy , těžkého Tloušťka cívky, válcované za tepla , slitina, Carbon , strukturální , vysokopevnostní nízkolegované , a High - Low- Alloy pevnost se zlepšeným Tvařitelnost , Všeobecné požadavky na

NORMA vydána dne 1.11.2015

Jazyk
Provedení	PDF - okamžité stažení - 1 997.90 Kč Tištěné - 1 997.90 Kč
Dostupnost	SKLADEM
Cena	1997.90 Kč bez DPH
1 997.90 Kč

Informace o normě:

Označení normy: ASTM A635/A635M-15
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2015
Kód zboží: NS-620462
Počet stran: 15
Přibližná hmotnost: 45 g (0.10 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Výrobky z ploché oceli a polotovary

Anotace textu normy ASTM A635/A635M-15 :

Keywords:

carbon, commercial, drawing, heavy thickness coils, high-strength low-alloy, high-strength low-alloy with improved formability, sheet steel, strip steel,, ICS Number Code 77.140.50 (Flat steel products and semi-products)

Doplňující informace

1. Scope

1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.

1.2 It applies to Specifications A414/A414M, A424/A424M, and A1018/A1018M.

1.3 This material is available only in coils described as follows:

Size Limits, Coils Only

Product

Width, in. [mm]

Thickness, in. [mm]

Strip

over 8 to 12, incl
[over 200 through 300]

0.230 to 1.000, incl
[from 6.0 through 25]

Sheet

All Widths^A
All Widths

0.230 to 1.000, incl
[from 6.0 through 25]

Note 1: The changes in width limits with the publication of A635/A635M – 06a result in a change in tensile testing direction for material from 0.180 in. [4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in. [1200 mm] wide, as that material is now covered by Specification A568/A568M – 06a. The purchaser is advised to discuss this change with the supplier.

1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.

1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification is used.

Note 2: The term weight is used when inch-pound units are the standard. However, under SI, the preferred term is mass.

1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.

2. Referenced Documents

A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products
A941-23	Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A1018/A1018M-23a	Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength (Includes all amendments and changes 12/8/2023).
A700-14(2019)	Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A568/A568M-19a	Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for (Includes all amendments and changes 11/22/2019).
MIL-STD-129	Marking for Shipment and Storage
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E11-22	Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
A1073/A1073M-21	Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
A424/A424M-18	Standard Specification for Steel, Sheet, for Porcelain Enameling
A414/A414M-23	Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels
A370-23	Standard Test Methods and Definitions for Mechanical Testing of Steel Products

Doporučujeme:

Aktualizace technických norem

Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.

Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.