Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Normalized High-Strength Low-Alloy Structural Steel Plates
Automaticky přeložený název:
Standard Specification pro normalizovaný High-Strength Low-Alloy strukturální ocelových plechů
NORMA vydána dne 15.10.2013
Označení normy: ASTM A633/A633M-13
Poznámka: NEPLATNÁ
Datum vydání normy: 15.10.2013
Kód zboží: NS-3452
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
bolted construction, high-strength, low-alloy, low ambient temperatures, normalized, notch toughness, plates, riveted construction, steel, structural steel, welded construction, ICS Number Code 77.140.10 (Heat-treatable steels)
1. Scope | ||
1.1 This specification covers normalized high-strength low-alloy structural steel plates for welded, riveted, or bolted construction. 1.2 This material is particularly suited for service at low ambient temperatures of −50°F [−45°C] and higher where notch toughness better than that expected in as-rolled material of a comparable strength level is desired. 1.3 Four grades, designated Grades A, C, D, and E (essentially former Specification A633 without a grade designation) are covered by this specification. Grade A provides a minimum yield point of 42 ksi [290 MPa] in thicknesses through 4 in. [100 mm], inclusive. Grades C and D provide a minimum yield point of 50 ksi [345 MPa] in thicknesses up to 2.50 in. [65 mm], inclusive and 46.0 ksi [315 MPa] in thicknesses over 2.50 in. to 4.0 in. [65 to 100 mm], inclusive. Grade E provides a minimum yield point of 60 ksi [415 MPa] in thicknesses up to 4.0 in. [100 mm], inclusive and 55 ksi [380 MPa] in thicknesses over 4 in. to 6 in. [100 to 150 mm], inclusive. 1.4 Current practice normally limits plates furnished under this specification to the maximum thicknesses shown in 1.5 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. |
||
2. Referenced Documents | ||
|
Historická
1.11.2012
Historická
1.10.2009
Historická
1.10.2009
Historická
1.11.2013
Historická
1.9.2010
Historická
1.10.2010
Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 02.05.2024 (Počet položek: 2 896 910)
© Copyright 2024 NORMSERVIS s.r.o.