Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM A599/A599M-07(2017)
Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet
Přeložit název
NORMA vydána dne 1.9.2017
Informace o normě:
Označení normy: ASTM A599/A599M-07(2017)
Datum vydání normy: 1.9.2017
Kód zboží: NS-796619
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM A599/A599M-07(2017) :
This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. The material shall conform to specified chemical composition requirements. The mechanical property requirements for structural steel, high-strength low-alloy steel with and without improved formability, commercial steel, and deep drawing steel are presented in details. The weight [mass] of coating shall conform to specified requirements fit for individual coating designations. The typical methods for determination of tin coating weights are described.
Keywords:
ICS Number Code 77.140.50 (Flat steel products and semi-products)
Doplňující informace
| 1. Scope | |||||||||||||||||||||||||||
|
1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Table 1. TABLE 1 Electrolytic Tin-Coated Sheets Coating Weight [Mass] Note 1: Listed below are the commonly produced coating weights
[mass] upon agreement between the producer and the purchaser. Other
combinations of coatings may be specified and the appropriate
minimum average test valuesA apply.
1.1.1 Electrolytic tin-coated sheet is
customarily available as commercial steel (CS); drawing steel (DS);
deep drawing steel (DDS); extra deep drawing steel (EDDS), and
structural steel (SS). The tin coating is available as unmelted or
melted.
1.2 Limitations—This specification is applicable to orders in either inch-pound units (as A599), which is supplied in thicknesses from 0.015 in. to 0.036 in., or SI units [as A599M], which is supplied in thicknesses from 0.381 mm to 0.914 mm. For thicknesses lighter than 0.015 in. [0.381 mm], refer to A624/A624M [A624M]. 1.3 Unless the order shows the “M” designation [SI units], the product shall be furnished to inch-pound units. The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
|||||||||||||||||||||||||||
| 2. Referenced Documents | |||||||||||||||||||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
