Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet
Automaticky přeložený název:
Standardní specifikace pro výrobky z bílého plechu, elektrolytické Tin-Coated, válcované za studena plech
NORMA vydána dne 1.3.2012
Označení normy: ASTM A599/A599M-07(2012)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.3.2012
Kód zboží: NS-3282
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
ICS Number Code 77.140.50 (Flat steel products and semi-products)
1. Scope | ||
1.1 This specification covers cold-rolled steel sheet in coils or in cut lengths, tin-coated by electrodeposition. The product is commonly known as electrolytic tin-coated sheet, and is for applications that need good solderability, good surface appearance, and a degree of corrosion resistance. Tin-coated sheet is produced to various designations of tin coating, as outlined in Designation No. |
Nominal Tin Coating |
Minimum Average Coating |
5 (0.6/0.6) |
0.025/0.025 (0.6/0.6) |
0.02/0.02 (0.5/0.5) |
10 (1.1/1.1) |
0.05/0.05 (1.1/1.1) |
0.04/0.04 (0.9/0.9) |
15 (1.7/1.7) |
0.075/0.075 (1.7/1.7) |
0.06/0.06 (1.4/1.4) |
20 (2.2/2.2) |
0.10/0.10 (2.2/2.2) |
0.08/0.08 (1.8/1.8) |
25 (2.8/2.8) |
0.125/0.125 (2.8/2.8) |
0.11/0.11 (2.5/2.5) |
50 (5.6/5.6) |
0.25/0.25 (5.6/5.6) |
0.23/0.23 (5.2/5.2) |
75 (8.4/8.4) |
0.375/0.375 (8.4/8.4) |
0.35/0.35 (7.8/7.8) |
100 (11.2/11.2) |
0.50/0.50 (11.2/11.2) |
0.45/0.45 (10.1/10.1) |
1.2 Limitations—This specification is applicable to orders in either inch-pound units (as A599), which is supplied in thicknesses from 0.015 in. to 0.036 in., or SI units [as A599M], which is supplied in thicknesses from 0.381 mm to 0.914 mm. For thicknesses lighter than 0.015 in. [0.381 mm], refer to A624/A624M [A624M].
1.3 Unless the order shows the “M” designation [SI units], the product shall be furnished to inch-pound units. The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable (Includes all amendments and changes 12/29/2023). |
|
Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment |
|
Standard Specification for Tin Mill Products, Electrolytic Tin Plate, Single Reduced |
|
Standard Specification for Tin Mill Products, General Requirements [Metric] |
|
Standard Specification for Tin Mill Products, General Requirements |
|
Standard Test Methods for Determination of Tin Coating Weights for Electrolytic Tin Plate (Includes all amendments and changes 3/6/2024). |
|
Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for (Includes all amendments and changes 11/22/2019). |
Historická
1.5.2014
Historická
1.5.2014
Historická
1.11.2009
Historická
1.4.2013
Historická
1.11.2010
Historická
1.5.2014
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 04.11.2024 (Počet položek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.