Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM A589/A589M-06(2018)
Standard Specification for Seamless and Welded Carbon Steel Water-Well Pipe
Přeložit název
NORMA vydána dne 1.9.2018
Informace o normě:
Označení normy: ASTM A589/A589M-06(2018)
Datum vydání normy: 1.9.2018
Kód zboží: NS-899423
Počet stran: 12
Přibližná hmotnost: 36 g (0.08 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM A589/A589M-06(2018) :
This specification covers four specific types of plain end or threaded and coupled carbon steel pipe for use in water wells. Water well pipe are classified into four types according to grads: type I, drive pipe; type II, water-well reamed and drifted pipe; type III, driven well pipe; and type IV, water-well casing pipe. The steel for both seamless and welded pipe shall be made by one of the following processes: open-hearth, electric furnace, or basic-oxygen. Tensile test, tension test, and hydrostatic test shall be required to conform to the requirements specified.
Keywords:
carbon steel pipe, seamless steel pipe, steel pipe, water well pipe, welded steel pipe,, ICS Number Code 23.040.10 (Iron and steel pipes)
Doplňující informace
| 1. Scope | ||||||||||
|
1.1 This specification covers four specific types of plain end or threaded and coupled carbon steel pipe for use in water wells. 1.2 Each type of water well pipe shall conform to the following methods of manufacture and grade as specified on the purchase order: 1.2.1 Type I, Drive Pipe—Seamless or electric-resistance-welded, Grades A and B. 1.2.2 Type II, Water-Well Reamed and Drifted Pipe—Seamless or electric-resistance-welded, Grades A and B, or furnace-butt welded. 1.2.3 Type III, Driven Well Pipe—Seamless or electric-resistance-welded, Grades A and B, or furnace-butt welded. 1.2.4 Type IV, Water-Well Casing Pipe—Seamless or electric-resistance-welded, Grades A and B, or furnace-butt welded. 1.3 The values stated in either inch-pound units or in SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values in each system are not exact equivalents; therefore, each system is to be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. Note 1: The dimensionless designator NPS (nominal pipe size)
and DN (Nominal Diameter) have been substituted in this standard
for such traditional terms as “nominal diameter,” “size,” and
“nominal size.”
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||
| 2. Referenced Documents | ||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
