Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM A568/A568M-09
Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
Automaticky přeložený název:
Standardní specifikace pro ocel, plech, Carbon , strukturální, a High - pevnost, nízká slitiny , válcované za tepla a za studena válcované , obecné požadavky na
NORMA vydána dne 1.5.2009
Informace o normě:
Označení normy: ASTM A568/A568M-09
Poznámka: NEPLATNÁ
Datum vydání normy: 1.5.2009
Kód zboží: NS-3147
Počet stran: 28
Přibližná hmotnost: 84 g (0.19 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM A568/A568M-09 :
Keywords:
carbon steel sheet, cold rolled steel sheet, general delivery requirements, high strength low alloy steel, hot rolled steel sheet, steel sheet, structural steel sheet, Alloy steel sheet/strip--specifications, Carbon steel sheet--specifications, Cold-rolled steel sheet/strip--specifications, General delivery requirements--steel, Hot-rolled steel sheet/strip--specifications, HSLA (high-strength low-alloy) steel sheet/strip--specifications, Improved formability steel
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, A 1011/A 1011M, and A 1039/A 1039M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in 1.1, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification is used. Note 1—The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. |
||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
