Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM A568/A568M-00b
Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for (Includes all amendments And changes 8/16/2017).
Automaticky přeložený název:
Standardní specifikace pro ocel, plech, uhlíku a vysoce pevnostní nízkolegované , válcované za tepla a za studena válcované , Všeobecné požadavky na
NORMA vydána dne 10.3.2002
Informace o normě:
Označení normy: ASTM A568/A568M-00b
Poznámka: NEPLATNÁ
Datum vydání normy: 10.3.2002
Kód zboží: NS-3135
Počet stran: 28
Přibližná hmotnost: 84 g (0.19 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM A568/A568M-00b :
Keywords:
alloy steel sheet, carbon steel sheet, cold rolled steel sheet, general delivery requirements, high strength low alloy steel, hot rolled steel sheet, steel sheet, ICS Number Code 77.140.50 (Flat steel products and semi-products)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (ASTM Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29. 1.5 lists permissible variations in dimensions and mass (see Note 1) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. Note 1—The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units. |
||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
