Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM A385/A385M-22
Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip)
Přeložit název
NORMA vydána dne 1.11.2022
Informace o normě:
Označení normy: ASTM A385/A385M-22
Datum vydání normy: 1.11.2022
Kód zboží: NS-1090557
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM A385/A385M-22 :
This practice covers the precautions that should be taken to obtain high-quality galvanized coatings. Assemblies should consist of elements of similar chemistry and surface condition. Whenever different analyses of steel or different surfaces of steel are united in an assembly the galvanized finish is not generally uniform in appearance. These differences include excessively rusted surfaces, pitted surfaces, machined surfaces, cast iron especially with sand inclusion, cast steel, malleable iron, hot-rolled steel, and cold-rolled steel. All oil or grease should be removed from both the sheet steel and wire or rod before rolling. Welding flux residues shall be removed by standard galvanizing cleaning techniques and are best removed at the gun. All fabricated assemblies shall be so designed with vent and drain holes such that no air is trapped during immersion of the assemblies into cleaning solutions or molten zinc. Moving parts such as handles or hinges should be galvanized separately and assembled after galvanizing. All markings shall remain legible after galvanizing. When an assembly of steel parts or an individual steel part has been designed and fabricated with critical dimensions and must be subsequently hot-dip galvanized, the designer should be aware that the hot-dip galvanizing process chemical cleaning to prepare the surfaces for coating and this may alter the critical dimensions.
Keywords:
coatings-zinc, galvanized coatings, steel products-metallic coated, zinc coatings-steel products,, ICS Number Code 25.220.40 (Metallic coatings)
Doplňující informace
| 1. Scope | ||||||||||||
|
1.1?This practice covers the precautions that should be taken to obtain high-quality hot-dip galvanized coatings. 1.2?Where experience on a specific product indicates a relaxing of any provision, the mutually acceptable change shall be a matter for agreement between the manufacturer and purchaser. 1.3?UnitsThis practice is applicable to orders in either inch-pound units (as A385) or in SI units (as A385M). Inch-pound units and SI units are not necessarily exact equivalents. Within the text of this specification and where appropriate, SI units are shown in brackets. Each system shall be used independently of the other without combining values in any way. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
