ASTM A813/A813M-14..
ASTM A814/A814M-15e1..
ASTM A847/A847M-14..
ASTM A849-15
ASTM A861-04(2013)..
ASTM A872/A872M-14..
Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM A358/A358M-15
Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications
Automaticky přeložený název:
Standardní specifikace pro Electric - Fusion - svařované austenitické chrom - nikl trubky z nerezové oceli pro vysokou provozní teploty a normální prostředí
NORMA vydána dne 1.9.2015
Informace o normě:
Označení normy: ASTM A358/A358M-15
Poznámka: NEPLATNÁ
Datum vydání normy: 1.9.2015
Kód zboží: NS-614676
Počet stran: 9
Přibližná hmotnost: 27 g (0.06 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM A358/A358M-15 :
Keywords:
arc welded steel pipe, austenitic stainless steel, chromium-nickel steel, fusion welded steel pipe, high temperature application, steel pipe, temperature service applications, high, welded steel pipe ,, ICS Number Code 23.040.10 (Iron and steel pipes)
Doplňující informace
| 1. Scope | ||||||||||||
|
1.1 This specification2 covers electric-fusion-welded austenitic chromium-nickel stainless steel pipe suitable for corrosive or high-temperature service, or both, or for general applications. Note 1: The dimensionless designator NPS (nominal pipe size)
has been substituted in this standard for such traditional terms as
“nominal diameter,” “size,” and “nominal size.”
1.2 This specification covers the grades of alloy and stainless steel listed in Table 1. The selection of the proper grade and requirements for heat treatment shall be at the discretion of the purchaser, dependent on the service conditions to be encountered. 1.3 Five classes of pipe are covered as
follows:
1.3.1 Class 1—Pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed. 1.3.2 Class 2—Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required. 1.3.3 Class 3—Pipe shall be single welded by processes employing filler metal in all passes and shall be completely radiographed. 1.3.4 Class 4—Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition of filler metal (see 6.2.2.1 and 6.2.2.2). 1.3.5 Class 5—Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed. 1.4 Supplementary requirements covering provisions ranging from additional testing to formalized procedures for manufacturing practice are provided. Supplementary Requirements S1 through S6 are included as options to be specified when desired. 1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Podobné normy:
Historická
1.10.2014
Historická
1.3.2015
Historická
1.5.2014
Historická
1.5.2015
Historická
1.5.2013
Historická
1.5.2014
Doporučujeme:
EviZak - všechny zákony včetně jejich evidence na jednom místě
Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !
Chcete vědět více informací? Podívejte se na tuto stránku.
