Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM A307-21
Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength
Přeložit název
NORMA vydána dne 15.2.2021
Informace o normě:
Označení normy: ASTM A307-21
Datum vydání normy: 15.2.2021
Kód zboží: NS-1021921
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM A307-21 :
This specification covers the chemical and mechanical requirements for three grades (Grades A, B, and C) of carbon steel bolts and studs in specified sizes. This specification does not cover the requirements for machine screws, thread cutting/forming screws, mechanical expansion anchors, or other similar externally threaded fasteners. When tested, sampled specimens shall adhere to specified values for chemical composition, hardness, tensile strength, yield point, elongation, and dimensions.
Keywords:
all thread rod, bolts, carbon steel, steel, studs, threaded rod,, ICS Number Code 21.060.10 (Bolts, screws, studs)
Doplňující informace
| 1. Scope | |
|
1.1?This specification Grade |
Description |
|
? |
|
|
Grade A |
Bolts, studs, and threaded rod having a minimum tensile strength of 60 ksi and intended for general applications, |
|
Grade B |
Bolts, studs, and threaded rodA having a tensile strength of 60 to 100 ksi and intended for flanged joints in piping systems with cast iron flanges, and |
|
Grade C |
Replaced by Specification F1554 Gr.36 |
1.2?This specification does not cover requirements for machine screws, thread cutting/forming screws, mechanical expansion anchors or similar externally threaded fasteners.
1.3?Suitable nuts are covered in Specification A563. Unless otherwise specified, the grade and style of nut for each grade of fastener, of all surface finishes, shall be as follows:
|
Fastener Grade and Size |
Nut Grade and StyleA |
|
A 1/4?to 11/2?in. |
A, hex |
|
A over 11/2?to 4 in. |
A, heavy hex |
|
B, 1/4?to 4 in. |
A, heavy hex |
1.4?The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.5?Supplementary Requirement S1 of an optional nature is provided, which describes additional restrictions to be applied when bolts are to be welded. It shall apply only when specified in the inquiry, order, and contract.
1.6?Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein.
1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|
B?18.24 |
Part Identifying Number (PIN) Code System Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org. |
|
Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
|
|
Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series (Includes all amendments and changes 9/12/2023). |
|
|
Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
|
|
Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel |
|
|
Standard Test Methods and Practices for Chemical Analysis of Steel Products |
|
|
Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement (Includes all amendments and changes 2/22/2023). |
|
|
Standard Specification for Carbon and Alloy Steel Nuts |
|
|
B18.31.3 |
Threaded Rods (Inch Series) |
|
Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners |
|
|
B?1.1 |
Unified Screw Threads Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org. |
|
B?18.2.1 |
Square and Hex Bolts and Screws |
|
Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength |
|
|
Standard Terminology for F16 Mechanical Fasteners |
