Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM A307-04e1

Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength (Includes all amendments And changes 8/16/2017).

Automaticky přeložený název:

Standardní specifikace pro uhlíkové oceli šroubů a svorníků , 60 000 PSI pevnosti v tahu

NORMA vydána dne 1.8.2004

Jazyk
Provedení	Online zabezpečené PDF - 1 806.70 Kč Tištěné - 1 806.70 Kč
Dostupnost	SKLADEM
Cena	1806.70 Kč bez DPH
1 806.70 Kč

Informace o normě:

Označení normy: ASTM A307-04e1
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2004
Kód zboží: NS-1950
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM A307-04e1 :

Keywords:

bolts, carbon steel, steel, studs, ICS Number Code 21.060.10 (Bolts, screws, studs)

Doplňující informace

1. Scope

1.1 This specification covers the chemical and mechanical requirements of three grades of carbon steel bolts and studs in sizes 1/4 in. (6.35 mm) through 4 in. (104 mm). The fasteners are designated by "Grade" denoting tensile strength and intended use, as follows:

Grade	Description

Grade A	Bolts and studs having a minimum tensile strength of 60 ksi (414 MPa) and intended for general applications,
Grade B	Bolts and studs having a tensile strength of 60 to 100 ksi (414 to 690 MPa) and intended for flanged joints in piping systems with cast iron flanges, and
Grade C	Nonheaded anchor bolts, either bent or straight, having properties conforming to Specification A 36/A 36M (tensile strength of 58 to 80 ksi (400 to 550 MPa)) and intended for structural anchorage purposes.

1.1.1 The term studs includes stud stock, sometimes referred to as threaded rod.

1.2 This specification does not cover requirements for machine screws, thread cutting/forming screws, mechanical expansion anchors or similar externally threaded fasteners.

1.3 Suitable nuts are covered in Specification A 563. Unless otherwise specified, the grade and style of nut for each grade of fastener, of all surface finishes, shall be as follows:

Fastener Grade and Size	Nut Grade and Style^A
A, C, 1/4 to 11/2in.	A, hex
A, C, over 1 1/2 to 4 in.	A, heavy hex
B, 1/ 4 to 4 in.	A, heavy hex
^A Nuts of other grades and styles having specified proof load stresses (Specification A 563, Table 3) greater than the specified grade and style of nut are also suitable.

1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.5 Supplementary Requirement S1 of an optional nature is provided, which describes additional restrictions to be applied when bolts are to be welded. It shall apply only when specified in the inquiry, order, and contract.

1.6 Terms used in this specification are defined in Terminology F 1789 unless otherwise defined herein.

2. Referenced Documents

B?18.24	Part Identifying Number (PIN) Code System Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.
F1470-24	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
F788/F788M-20(2025)	Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series
F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
B695-21	Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
A751-25	Standard Test Methods and Practices for Chemical Analysis of Steel Products
A706/A706M-26	Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
A563-15	Standard Specification for Carbon and Alloy Steel Nuts
B18.31.3	Threaded Rods (Inch Series)
F2329-13	Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
B?1.1	Unified Screw Threads Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
B?18.2.1	Square and Hex Bolts and Screws
F1554-20	Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength
F1789-26	Standard Terminology for F16 Mechanical Fasteners

Doporučujeme:

Aktualizace technických norem

Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.

Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.